Search results

  1. Mango

    Intake Manifold Install

    Removed the IAC cleaned it check connections re installed took it for a small test drive no stall??
  2. Mango

    Intake Manifold Install

    Did that several times while checking codes, added a new ground strap to the frame cleaned out the bolt hole to remove thread sealant to get better ground Idles great rev it up sounds great short test drive across the parking lot stalled out Cleaned out all the electrical connections added...
  3. Mango

    Intake Manifold Install

    Location? Reset?
  4. Mango

    Intake Manifold Install

    No did not remove it but i will check it out??
  5. Mango

    Intake Manifold Install

    IAC??
  6. Mango

    Intake Manifold Install

    Yes, now no idle shuts down
  7. Mango

    Intake Manifold Install

    disconnected the EST Connector when timing ,on Zero And re connected ??
  8. Mango

    Intake Manifold Install

    Latest cleaned the electrical connections on the TPS and cleared the ECM codes gone? Went for a test drive engine light came on hard shift ran like it was going to stall! Checked codes now code 42 came up just replaced the ICM in June Checked the wires all looked good, Cleared the ECM again...
  9. Mango

    Intake Manifold Install

    Also pulling a code 24??
  10. Mango

    Intake Manifold Install

    Well its done had to re set the timing no big deal Now it has low idle and when revving the engine at operating temp it stalls, hard starts, Code 22 TPS gone bad?? It was fine before? did the throttle body cleaner damage it when i blasted it? Also Bent Kinked fuel Line trying to remove, not...
  11. Mango

    Intake Manifold Install

    Well its done have not started the engine yet draining the oil over night, however kinked the right fuel line during removal, not too bad but what could go wrong???
  12. Mango

    Intake Manifold Install

    Thanks for the Replies Touque Specs 25, 35? Ft Lbs
  13. Mango

    Intake Manifold Install

    Thanks PB Blaster on the Bolts now Plain on doing the project on Friday Just did a oil change looks like that will be changed after the install, should i also replace the filter? Best RTV?
  14. Mango

    Intake Manifold Install

    I am pulling the Intake Manifold off to replace the gaskets and other parts while it is off! Had a oil sample come back and the potassium lever was steady at 13 to 14 now 49 must be leaking!!! Cylinder at top dead center compression stroke before pullling the Dist? is this manadatory Any tips...
  15. Mango

    Replacing intake manifold+gaskets

    Well its Time to replace the intake Manifold Gasket Oil sample came back after a recent oil change,Potassium was holding arround 13 now spiked to 49! Cylinder at top dead center on compression stroke before pulling Distributer out? Any other Tips would be great first time attempting this...
  16. Mango

    I need help and to know what this truck is worth

    He should pay you to get it out of his yard Good Luck All The Best
  17. Mango

    Replacing intake manifold+gaskets

    Sounds Good! Also can i blow the coolant out of the Manifold with Air ?
  18. Mango

    Draining antifreeze before changing intake manifold

    Could you blow it out with Air
  19. Mango

    Replacing intake manifold+gaskets

    I am About to change my Intake Gaskets Should i Saok The Bolts first? With PB Blaster or similar product? 188,000 miles never been done! Afraid of breaking bolts at least one by Cylinder 2 where the leak is
  20. Mango

    Deleting the Catalytic Converter

    Ok is stays on not plugged or rotten with rust yet
  21. Mango

    Deleting the Catalytic Converter

    Hey All I still have the original Cat on my 89 Burb 350 188.000 miles what happens if I take it off? Back pressure issues? MILPG? No Emissions in Wyoming Thanks
  22. Mango

    Looking For Jeep Steering Shaft

    Still looking, some that I found are pined, others too short, I need 22" in length? No salvage yards near by had any.leads would be Great
  23. Mango

    Looking For Jeep Steering Shaft

    I have been looking for a jeep replacement steering shaft, for a 1989 chevy burb 4x4 not made in China, found some for hundreds, not trying to break. the bank, one that would last Any leads would be great Thanks
  24. Mango

    Clicking in Steering Gear?

    yes i am wondering the same ??
  25. Mango

    1987 6.2L 4x4 new to me and new to here!

    Nice Burb no rust I recently replaced everything in the front steering, New Rag joint still has play going to upgrade to a jeep steering shaft

Latest posts

Forum statistics

Threads
45,561
Posts
986,264
Members
38,645
Latest member
sallyjeank10
Top