Search results

  1. Mango

    Intake Manifold Install

    PROGRESS: Removed the Distributor, ICM was loose, checked wires, Disconnected the ICM Plug Wires, Blasted it with electrical contact cleaner , and the Tan Brown connection used to set Timing. Went for a few short drives, No Engine light, No Stalling!
  2. Mango

    Intake Manifold Install

    Thanks back at it tomorrow , Started it up no check engine light went for a ride ran great no check engine light Turned it off checked for codes yep still there
  3. Mango

    Intake Manifold Install

    What wire are you talking about?
  4. Mango

    Intake Manifold Install

    Update Replaced the ICM, New Rotor, The Distrubuter Cap Coil Connection was loose, installed a new one attached all the plug wires in the correct location Went for a test drive ran great! Back to shop tested timing Was spot on, Cleared the code 42, Started right up, Let it Idle for a bit. Shut...
  5. Mango

    Oil Pan Gasket

    Hey All I seem to have oil leaking a little and getting worse, just replaced intake Manifold Gasket, Plenty of goop on the wall of China, unless it fell off? But its been dripping a little before the install. Rear Main Seal Flex Plate no Oil Does this year have a one piece gasket or old...
  6. Mango

    Reverse lights don't turn on.

    I added my own reverse lights, spot lights on a separate manual switch works great, especially when the guy behind you has their high beams on, one quick flip of the switch and wow what a response
  7. Mango

    New member

    Oh ya there, my wife is from Minnesota there now visiting the Fam Welcome
  8. Mango

    Intake Manifold Install

    AC Delco from Napa will be here Wed cheep ones die from the heat what do you put under the ICM, what it comes with or something better Thank You
  9. Mango

    Intake Manifold Install

    Need a new Ignition Control Module, Interesting did not have any issues before
  10. Mango

    Intake Manifold Install

    In the Process Now Thanks
  11. Mango

    Intake Manifold Install

    Yes still Code 42 going to check the wires to the ECM next The intake ports for the EGR were plugged used the old EGR could this be a issue
  12. Mango

    Intake Manifold Install

    GMBellew Checked all vac lines correct location most are new The T in the PCV line is Purge Signal Hose to canister Checked connections and wires look good Cleared codes let it idle to temp stalled when it reached Operating Temp Restarted it no engine light, idle was fine then idle dropped...
  13. Mango

    Intake Manifold Install

    Trying to find the issues
  14. Mango

    Intake Manifold Install

    Original Harness Wire Mold, wish it would run
  15. Mango

    Intake Manifold Install

    Goes to the canister that was there the whole time thanks It does connect to the TBI Could a bad temp sensor cause stalling
  16. Mango

    Intake Manifold Install

    Why would they fail now after a intake manifold gasket replacement
  17. Mango

    Intake Manifold Install

    Would a old ignition pick up cause the random stalling, it was fine before i pulled out the Distributor
  18. Mango

    Intake Manifold Install

    Rusty Nail EST wire clear thx Large ground strap to frame
  19. Mango

    Intake Manifold Install

    Yes Code came Back Where would I find That Manual
  20. Mango

    Intake Manifold Install

    That is Exactly where mine is, I painted the intake and used thread sealer would that be an issue? Rusty Nail what is your suggesion to locate the Grounds, Battery And small wire ground?? It was all fine before i Installed new Gaskets
  21. Mango

    Intake Manifold Install

    Added a additional ground strap to the frame, Cleaned surfaces to metal, Same issues runs for anwhile or drive Afew miles and instant shut off Move thhe ground to a new location?
  22. Mango

    Intake Manifold Install

    Thereis a ground on the Passenger side second bolt in the intake with the battery ground Check and was some bare wire repaired last year some time
  23. Mango

    Intake Manifold Install

    Thanks Guys No ground by the thermo
  24. Mango

    Intake Manifold Install

    UpDate code 23 gone code 33 vacuume hose not connected, The Dreaded code 42 is back checked ground wire ok Let it idle sounded great then just shut down no sputer its like i turned the ignition off hard start rough idling engine light came on Stumper
  25. Mango

    Intake Manifold Install

    Yes no stall, just Questioning if thats all it was I did clean the TBI when it was off with carb cleaner turned it upside down and blasted it must of gotten junk where it should not be Thanks

Latest posts

Forum statistics

Threads
45,561
Posts
986,266
Members
38,645
Latest member
sallyjeank10
Top