Search results

  1. Mango

    Throttle cable way too long

    Same issue this is the third cable on my burb, first two were before i owned it New cable seemed an bit long but it was the same ad the one that broke at the peddle connection? Started sticking almost immediately, Sprayed Motorcycle cable lube little help just getting worse, greased the bottom...
  2. Mango

    New member, long time square body owner

    :welcome:
  3. Mango

    Oil Leak

    Oil Leak, Head gasket can this leak on the drivers side Back of engine ? Replaced the Intake Manifold recently ant the oil really started to drip it leaked a little before now it really leaking on the drivers side! Pulled things off to replace the intake manifold gasket and saw the Distributor...
  4. Mango

    350 TBI high idle

    Figured it out the Cruse control linkage was the culprit! Checked idle screw and was not touching throttle plate A quick adjustment and all good now
  5. Mango

    350 TBI high idle

    @gmbellew I Have some of the same issues , High Idle will kick dows some when i give a good rev in park, In the moarning with block heater on all night starts up with the correct idle drive to work 10 miles park high idle?? I recently replaced the intake manifold gasket, Removed the IAC and...
  6. Mango

    Rear Main Seal

    @Ricko1966 Its a 4x4
  7. Mango

    Rear Main Seal

    @newguy11 I am planing on inspecting that again With a camera, If its the culprit off comes the intake and better RTV Ultra Black!!!
  8. Mango

    Rear Main Seal

    @squaredeal 1989
  9. Mango

    Rear Main Seal

    Yes replaced the gasket on the Dist twice Over tightened the first
  10. Mango

    Rear Main Seal

    Have you used Bars Rear Main Seal Product to stop rear main seal leaks I though I had a small leak that grew after replacing intake manifold gaskets! The oil leak is getting worse now blowing under the truck to the rear axel spotty and more oil on the ground I am convinced its the rear main or...
  11. Mango

    Inner fenderwell rust

    I had the same issue, Removed all the rusty metal, Used some thick sheet metal and fab to fit, Silconed the back, Installed with rivetts and self taping screws, Sprayed it with Flex Seal severial coats, SO far all good, my Burb is not pretty just a valley ride Cheap and easy. For a better...
  12. Mango

    O2 Sensor Testing

    Can you test a Single Wire O2 Sensor with Multi Meter in OHMS
  13. Mango

    Intake Manifold Install

    Well Well Still dripping Oil! Oil Pan seal? Rear Main Seal? Intake Manifold Seal on the back side ? Going to drop the Dye in and hopefully see the issues? New issues Seems to idle high in park when engine up to temp IAC gone Bad ? was fine before
  14. Mango

    Intake Manifold Install

    Looks like the Distributors was over torqued, seal was crushed on one side? Did not pull the Manifold Re torqued the bolts to 30 one was super loose ground wire attachment Now wait and see it that was it
  15. Mango

    Intake Manifold Install

    30 it will be
  16. Mango

    Intake Manifold Install

    Well doing the Intake Man Gaskets Again tomorrow using Ultra Black RTV and moving the fuel lines completely out of the way!!! What is the torque values for the Manifold Bolts? I set them at 25 ft lbs, and it leaked from the back China Wall I think? Saw a video set at 35 Ft lbs, Other at 30 ft...
  17. Mango

    New here from AZ

    Hello From Wyoming!
  18. Mango

    New here from the Wet Coast of Canada

    Nice ride Welcome from Wyoming
  19. Mango

    Intake Manifold Install

    @Rusty Nail, Double Dingo There is no place to use the Hood lined with insulation I have a solution a Gallon of Gas and a Match Walk to work its only eight miles one way
  20. Mango

    Intake Manifold Install

    @DoubleDingo I could get one out of the way but not the other I will have to unbolt the bracket a pain to get it back
  21. Mango

    Intake Manifold Install

    @DoubleDingo My Bad wrong file work related I posted the correct one this time
  22. Mango

    Intake Manifold Install

    Fuel Lines Not sure if you can pull this up
  23. Mango

    Intake Manifold Install

    @RustyNail Double Dingo How to keep the fuel lines out of the way
  24. Mango

    Intake Manifold Install

    @DoubleDingo when you repaired, replaced the RTV did you install new gaskets or use the same ones? I did not let it set long enough before torquing the bolts, let it sit for a day before running it no leaks at the time Thanks
  25. Mango

    Intake Manifold Install

    @DoubleDingo Grey FelPro RTV going to use black next time and get the fuel lines out of the way somehow

Latest posts

Forum statistics

Threads
45,561
Posts
986,264
Members
38,645
Latest member
sallyjeank10
Top