Search results

  1. H

    Best split bench option

    I ordered these for my truck along with brackets that fit my truck and waiting on them. It takes a couple months to make them. https://shop4seats.com/truck-seats/40-20-40-truck-seats/all-bench-seats.html
  2. H

    Fuel pump wiring issue LS Swap

    It goes to any ignition "on" fuse under dash. Get test light and probe, Either piggy back a fuse or find an unused ignition socket and buy the right plug.
  3. H

    Serpentine Belt brackets

    My expensive GM serpentine belt kit with AC compressor on passengers' side has tall valve covers because I am using old Crane gold roller rockers. I did have to clock the alternator and will not be using the brace unless I can refigure it.
  4. H

    Chose between the vortec vs sbc

    If it's .060 over now it can't be bored again if needed. Boat anchor.
  5. H

    LMC Tach Kit Install

    It's probably only key on for lighted gauge. The tach gets all it needs from coil in distributor.
  6. H

    Replacing intake manifold+gaskets

    I don't believe teflon tape is made for that to be honest. The Arp thread sealant works well sealing just about everything on an engine. The Permatex above probably works just as good too! https://www.summitracing.com/parts/arp-100-9904
  7. H

    Replacing intake manifold+gaskets

    I would not use rtv but I have in the past and that stuff is hard to get out later if ever needed. I would chase holes with a tap and use Arp thread sealant instead.
  8. H

    Serpentine Belt brackets

    https://www.summitracing.com/parts/nal-19418818 Way overpriced. :( It does include everything shown including power steering pump. It sure is smooth running though.
  9. H

    Serpentine Belt brackets

    This is a pic of a new GM serpentine kit from Summit. It matches a stock kit but I am not sure which.
  10. H

    R10 Fan

    This fan will work. https://www.summitracing.com/parts/rnb-621-108 along with this clutch https://www.rockauto.com/en/moreinfo.php?pk=1141191&cc=1061570&pt=6812&jsn=581 Both are CCW rotation.
  11. H

    What have you done to your square lately??

    Did you buy different shocks or using stock?
  12. H

    Broken shift tube?

    I don't know tbh.
  13. H

    Broken shift tube?

    It no longer meets safety guidelines for crash and is there to protect you. All vehicles since around 1960 something are required to have this feature.
  14. H

    Broken shift tube?

    Those plastic pieces are part of the safety mechanism that collapses the column in case of accidents. There is no way that I know of to fix it except to replace the steering column.
  15. H

    What have you done to your square lately??

    Which coils did you use and did you use coil spring compressor? Stock spindles or lowered?
  16. H

    What have you done to your square lately??

    Yes they are the 40's.
  17. H

    What have you done to your square lately??

    4" speedo and tach while smaller gauges are 2- 1/16. It was not easy to do but I took my time fitting everything. They do not fit the holes without enlarging. The hardest was cutting the new expensive gauge bezel in the back. I used several methods to shave off the back to sit flush. I even...
  18. H

    What have you done to your square lately??

    Indeed they are! I modified the stock pod and used metal instead of the plastic piece to hold the gauges after enlarging the holes. The new gauge bezel I am going to use was modified in back to sit flush like a stock unit. The Speedhut gauges have a lower profile in the back which is nice and...
  19. H

    What have you done to your square lately??

    I bought a full set of Bilstein shocks and got the front pair installed. The rear shocks will be installed tomorrow. The ones I took off were shot and IIRC, those came from Autozone several years back. Pics will be added later. The CSI water neck got a new set of O rings too.
  20. H

    What have you done to your square lately??

    I took a few with flash above!
  21. H

    What have you done to your square lately??

    I will have to get some pics later. It's dark now. The Flowmasters sound good! Still need tidy up a bit and install new gauge bezel and dash pad. The new throttle assembly from Hotrod Innovations and Lokar cable rocks!
  22. H

    What have you done to your square lately??

    I just finished up on the many upgrades and I finally started it up the other day. Turned key to ignition, checked for fuel leaks and get fuel pressure instantly. Cranked on first try. No pumping the gas pedal and you would think its fuel injected. (I never experienced a carbed motor like this...
  23. H

    Exhaust replacement- anyone do it without welding?

    I made 2 cuts with my cold saw and re-welded the piece shaped like pic. Of course, it was rounded corners.
  24. H

    Exhaust replacement- anyone do it without welding?

    I used Doug's ceramic coated Tri-Y. In reviews, it says headman headers fit but another guy did what I did and shortened crossmember piece.
  25. H

    Exhaust replacement- anyone do it without welding?

    Which headers are you using? I installed the 2 1/2" Flowmaster kit on my 86. Fit was good but depending on which headers. I had to cut & shorten, re-weld the pipe in the middle that goes over the crossmember on DS.

Latest posts

Forum statistics

Threads
48,675
Posts
1,074,350
Members
43,350
Latest member
Johns C10 Hubcap
Top