Search results

  1. AZ Highlander

    Dino's Git Down 2023

    Wish I could make it, but family stuff came up so I am holding it down up here in Prescott. enjoy it!
  2. AZ Highlander

    Hey everybody I'm Anthony an auto tech from Tucson Arizona. I look forward to getting involved with this discussion forum.

    welcome from Prescott, Arizona! :welcome:
  3. AZ Highlander

    700R4 TV cable - weird adjuster?

    Great pictures Patrick. Thank you very much for sharing.
  4. AZ Highlander

    700R4 TV cable - weird adjuster?

    These should really help. Going to look at them in the am when I have time to head out to the truck. Thanks Patrick.
  5. AZ Highlander

    700R4 TV cable - weird adjuster?

    Thanks Patrick. Yes, edelbrock intake and their 1406 carb. My throttle cable comes at a weird angle too. Might need to fabricate something like you did to get the throttle cable and TV in a better position to one another. I wonder what the best bracket is for our trucks with Edelbrock...
  6. AZ Highlander

    700R4 TV cable - weird adjuster?

    Should I just get a new TV cable adjuster? Mine does not have the ability to adjust automatically using the throttle cable. At least I don't think it does. Is anyone familiar with this style of adjuster? I'm not even sure how to adjust it properly if its possible. Below are the instructions I...
  7. AZ Highlander

    700R4 TV cable - weird adjuster?

    I have a 700 R4 and what appears to be an unconventional screw type adjustment for the TV cable. I read the instructions that are linked through summit racing‘s website here, but can’t figure out what the best way to adjust my TV cable would be. I have 4.10 gears turned by a 350 through the...
  8. AZ Highlander

    Let's see those 4x4 Squares On Dirt!

    Finally got the 87 out on some dirt outside Prescott, AZ with my son and our ranch dog.
  9. AZ Highlander

    @NickTransmissions

    Hey Patrick, I have been following along since the beginning of the thread because I have the same trans and not confident it was setup correctly with the carb. I haven't driven it much yet. I am confused about the quoted post above. Wasn't your trans shifting into second at 15-20mph a week ago...
  10. AZ Highlander

    Dana 44 dust shield on backing plates

    It might work that way, but not work the other way around? I tried 10 bolt calipers on D44 with no success
  11. AZ Highlander

    Dana 44 dust shield on backing plates

    The calipers I purchased for the 10 bolt didn't fit on the rotors/backing plate of the D44. Barely different, but would not sit down on the rotor enough to put the caliper pins/bolts through the holes completely. The calipers for the D44 fit perfectly first try however.
  12. AZ Highlander

    Dana 44 dust shield on backing plates

    I found out the hard way that the brake calipers are not the same. Not sure what else.
  13. AZ Highlander

    Squarebody Down! HELP - Member Roadside Assistance Volunteer Map

    Got you added. Access the map here: https://www.google.com/maps/d/u/0/e...&ll=37.60570580479403,-102.94947032558306&z=5
  14. AZ Highlander

    Bad Master Cylinder?

    These are brand new wheel cylinders by the way. What did I do wrong? It seemed like just a little brake fluid was coming out slowly from the bleeder when I cracked it. Then it started making a leaking noise and I saw it flowing down the bottom of the tire on the back of the wheel. Why would the...
  15. AZ Highlander

    Bad Master Cylinder?

    So, that worked. Got the master to bleed. Was obviously sucking air back into the master through the rear line before. Finger was a one way valve over the rear line hole. Success! But the saga continues…. Went to bleed the right rear, fluid started coming out! Success! Then I heard a leak...
  16. AZ Highlander

    Bad Master Cylinder?

    The friend I got the master from told me to remove the lines off the master and use my fingers over the holes to prevent air from getting sucked back in while my son pumps the pedal. Will try that technique later this afternoon. Thanks for the tips guys!
  17. AZ Highlander

    Bad Master Cylinder?

    Thanks Casey. I was hoping to avoid buying the kit to bleed back into itself, but I may need to bite the bullet. Bleeding without it isn't working for me yet.
  18. AZ Highlander

    What have you done to your square lately??

    yeah, I think most, if not all of the really bad potholes were west of Flagstaff. They happened this past winter in early 2023.
  19. AZ Highlander

    Bad Master Cylinder?

    It is showing Bleeding the master cylinder is not working. I could be doing it wrong, but can’t get all the air out of the master. Isn’t that the first thing to do? From all I’ve read and watched, you can bleed the master on or off the vehicle and it doesn’t need lines attached.
  20. AZ Highlander

    Bad Master Cylinder?

    Same result with my friends master cylinder. It seemed like the rear was bleeding ok for the first crack, then got worse the next few times, then this on the fourth or fifth
  21. AZ Highlander

    What have you done to your square lately??

    You’re not joking Paul. Have you driven on I40 much this year west of Williams? Pothole city.
  22. AZ Highlander

    Bad Master Cylinder?

    Got one from a friend but haven’t had a chance to install it yet
  23. AZ Highlander

    Bad Master Cylinder?

    Thanks Eric. I have that one in my cart as I type this. I plan to order it immediately after a failed bleed attempt on the one I am picking up from my friend.
  24. AZ Highlander

    Bad Master Cylinder?

    I plan to. Not getting fluid out both sides of the master cylinder at the moment however.
  25. AZ Highlander

    Bad Master Cylinder?

    It turns out I have a friend in the next town over with a master cylinder he pulled and kept around after he installed hydroboost. Things are looking up!

Latest posts

Forum statistics

Threads
48,667
Posts
1,074,231
Members
43,339
Latest member
Jeremy89
Top