Search results
-
Finally found another Square Body....
Nice looking truck. Does need some fatter meats. Welcome to the show.- brooksman9
- Post #6
- Forum: Introduction
-
-
Time traveler with a squarebody. My clock is ticking backwards.
They are easy to repair. I think all you have to do is file the little contacts and a little wd40. Look for a youtube video. Did the one in my Camaro years ago. Still working.- brooksman9
- Post #2
- Forum: Electrical & Audio
-
Rough country lift
I had ordered a 2" tuff country lift for mine. Finally had to cancel the order over a month later after several delays from them. Wound up with a 2.5" sky jacker. Good luck.- brooksman9
- Post #26
- Forum: Lifted & Off-Road Systems
-
-
-
-
Cowl removal difficulty level
Had the same problem on my 86. Although I was blowing apart to paint so I wound up taking it off.- brooksman9
- Post #19
- Forum: Tech Discussion
-
Dave Nelsen here in northern Wyoming. Started working on Chevys in 1966, (1951 216 C.I. in 1952 Chev. car. FAST FORWARD after Nova's, Impalas, etc.
Welcome Dave Nelson (from nastyz28)- brooksman9
- Post #13
- Forum: Introduction
-
Latest Lost Cause Project: 1979 Z28
Do love a 2nd gen F-body. Have a 73 now and have had several others. Although for some strange reason I am wanting a 1st gen now. ;)- brooksman9
- Post #13
- Forum: Other Vehicles
-
-
What have you done to your square lately??
I could use one! Installed a new radiator to replace the leaking like a sive one that it came with. Test drive went much better today. Still have the crank issue. May have to bite the bullet and get a new battery.- brooksman9
- Post #23,041
- Forum: Garage
-
What have you done to your square lately??
Hate them little bastages- brooksman9
- Post #23,036
- Forum: Garage
-
84 K10 full exhaust replacement
You are nuts... just like the rest of us. Curious to see what you wind up going with. Pics when done please. Always been a big fan of headers but those Hookers are just sexy!- brooksman9
- Post #4
- Forum: Engine & Performance
-
Th350 not spinning the speedo cable
There is also a clip on the drive gear on the tail shaft that keeps it in place. If it’s missing it can slide back an not contact the driven gear. Pull the housing from the tranny and spin as a unit. If the needle moves check the gear on the shaft.- brooksman9
- Post #3
- Forum: Garage
-
What new tools have you got lately?
Nice. Did that last year. Just on a smaller scale.- brooksman9
- Post #2,558
- Forum: Garage
-
custom carpet and headliner
Welcome Jack. You can get some headliner material at a fabric store and use a good spray glue to replace that. As far as the carpet goes I'd go with an ACC brand that you can get at one of the suppliers or even Amazon which is where I got mine I believe.- brooksman9
- Post #2
- Forum: Interior
-
-
My 700r4 changes too early ?
Nice looking truck- brooksman9
- Post #6
- Forum: Transmission & Transfer Case
-
-
-
-
What have you done to your square lately??
Haven't really spent much time in that thread. Pic was not taken for the challenge though so wouldn't that disqualify it?- brooksman9
- Post #23,011
- Forum: Garage
-
What have you done to your square lately??
Yep. Bolt/plug for holding the fuel pump rod in place during installation missing. Had the same issue on one of my Camaros years ago. Lots of oil (I say lots, probably not that much) on the steering linkage just below there. Only comes out while driving. Perhaps a little spirited driving. I know...- brooksman9
- Post #23,009
- Forum: Garage
-
What have you done to your square lately??
Fixed an oil leak today from yesterday's test drive. See if you can figure out where.- brooksman9
- Post #23,006
- Forum: Garage
