Search results

  1. skysurfer

    Sanden Condenser Compatibility

    I In reading the linked thread above, it looks like Viktor was able to use the stock hoses by adding the ATC6302 adapter. Were you satisfied with the quality of the hoses you got from coldhose? I have a feeling I’ll need their services for something. The odds of ordering a bunch of parts...
  2. skysurfer

    Sanden Condenser Compatibility

    I should be able to use the stock hoses, or I should say the stock style hoses as I'm replacing the oem ones due to their age. I'm going to follow the directions @yevgenievich posted in his thread since he has what is essentially the same vehicle...
  3. skysurfer

    Sanden Condenser Compatibility

    For those that have swapped to a Sanden compressor and r134, what are you using for a condenser? I've started ordering ac parts since my R4, which has been growling for a long time, finally threw in the towel this weekend. In reading about the conversion, it's recommended to upgrade the...
  4. skysurfer

    SCAM ALERT New member Marionfeet

    Validation for the 50 post rule. This “Marion” has no forum posts and joined two days ago. Red flags everywhere.
  5. skysurfer

    best 10 Bolt gears for highway and low end torque

    What gears are in it now? I assume you are aware you have to do both ends, so your budget needs to be ready for that. Last issue is wanting low rpm on the highway but acceleration off the line. There’s no magic gear ratio that will get you both, so decide what’s more important.
  6. skysurfer

    AuroraGirl is buying another square... is it a good one?

    Those rockers...or what used to be rockers, are enough to make me walk away and not look back.
  7. skysurfer

    Factory roof rack install - I don't have the black gaskets, what can I use to make some?

    I would drill pilot holes first. You can buy self-tapping screws but they’re sort of a “wham bam thank you mam” approach to repairs and not something I’d use on a painted surface. Easiest way to figure out what size drill to use is to hold a screw up to the light with one hand and with your...
  8. skysurfer

    Cheap Substitue for 4 inch lift shocks ???

    Here's the specs for the shocks I have that are specifically made for a squarebody with a 4" lift. Front: Gabriel G63437 23.33" extended 14.05" collapsed 9.28" stroke Rear: Gabriel G63438 29.33" extended 17.30" collapsed 12.30" stroke
  9. skysurfer

    Factory roof rack install - I don't have the black gaskets, what can I use to make some?

    That's the strange thing, this was a factory installed rack and there are two types of hardware used. The forward-most screw on each side, along with the most-rearward screw on each side, are 8-32 n.c. machine screws. So four of those total. All the other screws are what appear to be #10 x 1/2"...
  10. skysurfer

    Factory roof rack install - I don't have the black gaskets, what can I use to make some?

    I was missing a couple of them and made some from material I got at Ace Hardware. It wasn't the right color but it's not something you'll notice after installation. This stuff was the right thickness and easy to work with. I tried to find the Ace stock number online but couldn't. This came as a...
  11. skysurfer

    Anyone here setup HEI and a MSD on their 87-91 tbi small block??

    I’ve never had a cel. (and yes, it does light up with ignition on so it’s not broken, lol) Currently running the stock AC Delco distributor but also have a MSD 8366 dizzy sitting on the shelf. That one is earmarked for another engine that I can never seem to get around to installing. The 8366...
  12. skysurfer

    Big Block Cooling w/Electric Fans: DON'T DO IT

    I recall somebody, maybe @gmachinz, mounted a big single efan inside the oem shroud. Seemed like the best compromise between the two systems.
  13. skysurfer

    Anyone here setup HEI and a MSD on their 87-91 tbi small block??

    Like I said, plug and play. I have a vague memory of messing with the coil bracket a little bit but it was so long ago I'd have to pull the air cleaner to be sure. If the MSD system did anything wonky it would've been yanked immediately. I wasn't looking to go this route but there was a local...
  14. skysurfer

    Anyone here setup HEI and a MSD on their 87-91 tbi small block??

    Yeah, 1989 5.7 TBI.
  15. skysurfer

    Anyone here setup HEI and a MSD on their 87-91 tbi small block??

    You talking about hooking up a typical MSD box or something else? I'm running a MSD 6A box with MSD 8226 coil. Using the 8876 wiring harness it was plug-and-play. Installed this in April 2008 and it's still going with zero problems.
  16. skysurfer

    The ultimate noob finally gets his dream truck - Hello from Joshua Tree

    Have you considered just mounting a large Con-Fer type rack on top of the factory rack? I wasn’t too thrilled with the idea of mounting anything attached to the gutters because they’re just screwed on instead of being a welded part of the roof. Something to consider if you plan on carrying any...
  17. skysurfer

    454 TBI doesn't like operating temperature!!!

    Well, it’s running fine and they say “don’t mess with success”, but it’s worth noting your fuel pressure is double what it’s supposed to be.
  18. skysurfer

    Advice 94, Z-71, 1/2 ton Rear Diff locker install

    Well, that confirms what you already knew...no traction-aiding option on it. I looked into the Z71 package a little more and it was basically just skid plates, Bilstein shocks, and a sticker. The gear ratio was usually, but not always, the GT4 3.73. As suspected, the G80 was a separate line...
  19. skysurfer

    Advice 94, Z-71, 1/2 ton Rear Diff locker install

    I always thought the G80 was included with the Z71 package but maybe it was listed as a separate line item.
  20. skysurfer

    Advice 94, Z-71, 1/2 ton Rear Diff locker install

    How do you know this? It would be helpful if you posted a pic of the sticker in the glove box.
  21. skysurfer

    Questions on TBI

    The stock setup was two 74lb injectors fed by a pump producing around 10-13psi. You installed 1995 injectors, I believe they are rated at 90lb/hr @ 30 psi. Now throw the '96 pump into the mix, it's my understanding they run at about 60 psi. How you're getting 90 psi is anyone's guess, but it's...
  22. skysurfer

    Questions on TBI

    I'm not familiar enough with the GMT400 tbi systems to answer all of your questions but I can help with the last one. I'm running an Aeromotive afpr and it's installed on the return line. The tbi systems build pressure by restriction, meaning that I didn't have to disable or modify the stock...
  23. skysurfer

    Is it better then a 1980 Square Body

    Grew up in Ventura but I’ve lived in Ojai for the last 30 years. Some of the pics in my album were taken at Casitas, back when there was water lol.
  24. skysurfer

    Is it better then a 1980 Square Body

    Close. This one is Lake Casitas. Cachuma is the next closest one going north.
  25. skysurfer

    Is it better then a 1980 Square Body

    Here's a useless factoid: That Ford is sitting on the bottom of our local lake. The paved road is an old highway which disappeared under water in 1962 after the dam was built but resurfaced a few years ago due to increased demand from development and ten years of below-average rainfall. The...

Latest posts

Forum statistics

Threads
48,667
Posts
1,074,229
Members
43,339
Latest member
Jeremy89
Top