Search results
-
What have you done to your square lately??
The wife and I made a couple of road trips in my daily square last year and have a couple more planned this year. I decided that I wanted to add a second saddle tank so I didn’t have to stop for gas so often. The only thing is I didn’t really want to modify my passenger bed side, so I took a... -
What have you done to your square lately??
This is also the Gen 2 kit, super easy to install with clear instructions and pictures. I had to swap positions with the low beam wire and the ground in the plug but no big deal and aiming was no difference than any other bulb and Zach is right new adjusters is almost required if you are still... -
What have you done to your square lately??
Well since the time change it is now dark both on the way to work and on the way home. So I finally decided to do the LED headlight conversion. It was pricey but it absolutely made a huge difference. I went with the RMS Lighting kit because I really liked the original look and the fact it had... -
Show your daily driver
The wife and I took my daily up to Fall Creek Falls in Tennessee this weekend to check out some pretty scenery.- Lugnut
- Post #1,055
- Forum: Other Vehicles
-
Wiper blades
They are the 15" but they actually measure about 15 1/2, so it's not really that noticeable.- Lugnut
- Post #10
- Forum: Glass & Mirrors
-
Wiper blades
Yes I am, I like the way they look and they work pretty good, would probably do better if my windshield was in better shape, it’s a little sandblasted. I wish they would make them a little longer. Oh yeah that reminds me I probably need another pair. Lol- Lugnut
- Post #8
- Forum: Glass & Mirrors
-
What have you done to your square lately??
Are you going to be able to get a windshield before C10’s in the city Saturday? -
Need help, '86 C10 AC condenser insulator.
I ended up finding mine on a '93 S10 in a junk yard. It was exactly the same part #. Good luck. -
AC Compressor
No problem, if it helps the OD is 7/8" with a 1/2" hole through it. You can go to your local hardware store and pick up a short pipe nipple and cut off the threads and cut the center to length for a few dollars and no one will know the difference.- Lugnut
- Post #6
- Forum: Tech Discussion
-
AC Compressor
The spacer on my '81 is 1.400" measured with a set of dial calipers. From the front of the compressor to the center of the belt groove is approximately 1.2" with an eyeball. Hope this helps.- Lugnut
- Post #4
- Forum: Tech Discussion
-
'81 bolt in high hump and clutch pedal assy.
I have a good NV3500 that came out of a '92 OBS that I am planning on using, so thats why I want a hyd. pedal assy. I know that are not know to be a strong transmission but it will be going behind a worn out 305 daily driver so I'm not to worried about it. That coupled with most of my wilder... -
Spray vs Plastic Bedliner
As far as the lower tie downs I used a u-bolt on the corners of the bed. I put a slight bend in them to make it a little easier to use. The rear ones I removed the taillight to gain access to the nuts. One of the best most useful things I’ve ever done to the truck.- Lugnut
- Post #12
- Forum: Paint and Body
-
'81 bolt in high hump and clutch pedal assy.
Yes I am very interested. Thanks -
'81 bolt in high hump and clutch pedal assy.
I am looking for a bolt in high hump for an '81 c10 for a 5-speed conversion, and a clutch pedal assy. for a hyd. clutch set-up. Thanks -
What have you done to your square lately??
These are the brackets for the shorter radiator. -
What have you done to your square lately??
From what I have seen a lot of the factory non-air and manual trucks got a shorter radiator. My '86 is factory air with a A833 4-speed had the shorter radiator. The upper radiator brackets are L-shaped and the fan shroud is also different. -
pin stripes
Holley also sells kits for our trucks. I have used one kit from Holley it was a little less expensive than Phoenix Graphix, and it went on just fine and looked good. I have used a couple from Phoenix, I think they may have a better selection of colors, with no problems. I installed a kit from...- Lugnut
- Post #5
- Forum: Introduction
-
Question about headers
Hooker is making cast iron manifolds that look pretty good and are supposed to flow a lot better than the stock ones. I haven't tried any yet but that is what I am leaning toward on my next engine swap.- Lugnut
- Post #24
- Forum: Engine & Performance
-
Probably the worlds worst question… can any ID this.
Windshield wiper delay module.- Lugnut
- Post #4
- Forum: Electrical & Audio
-
Need ideas for a modern steering wheel.
Comfort Grip is the name of it, I'm pretty sure it is made by OER (Original Equipment Reproduction) but not 100 percent on that. 15" dia. and the overall dish is 3 7/8" including the adapter. I will say this, it sat out in the direct Georgia sun about 6-7 hours this past Sunday and while the... -
Need ideas for a modern steering wheel.
I installed one of these comfort grip wheels on mine about a month ago and so far I love it. If I remember right it was about $200 with the adapter kit and horn button. Very easy to install and horn works great. -
Looking for a shift knob.
I had a red 3 billiard ball on mine for a few years but the sun finally turned it pink. I bought this q-ball and had my son who works for a machine shop mill in my pattern on it. I have always liked the feel of the bigger billiard ball as a shifter knob. -
Do aftermarket speaker mounts make 6x9's clear the cab?
Thanks, no I had a buddy powder coat it with a crinkle finish black. -
What have you done to your square lately??
Thanks, it turned out better than I thought it would. -
What have you done to your square lately??
Thanks, it’s been a long process. This is a before pic.
