Search results

  1. mtbadbob

    1976 Square drivers side A/C Duct

    My '87 just has a small, snorkel shaped outlet, about 1"w x 1/2" h, that blows straight down under the column
  2. mtbadbob

    New member from Cloverdale, CA

    Welcome from Montana! Sweet little Shortie!
  3. mtbadbob

    1976 Square drivers side A/C Duct

    If you can wait a few days, I'll try to grab it later in the week, should have it by weeks end. I'm guessing it won't be very expensive, but could be $40-$50 shipped. Lmk what you think...Bob
  4. mtbadbob

    1976 Square drivers side A/C Duct

    I believe they are the same through the '92 Squares. I can get my hands on one in the back of a 'Burb at a yard I frequent near me, if it's the duct work in the picture. It goes from main heater box behind ash tray, runs under steering column, attaches to lower column plate in the center, then...
  5. mtbadbob

    Tachometer replacement thoughts

    Ah, I see. Yeah, I found a factory tach out of a C30 for my '64 C10 and had it calibrated for a V-8 for the 409 going in it. It's super-nice as I restored the needle and all. I haven't seen any C10's or 20's with a factory tach before, I like that rare stuff!
  6. mtbadbob

    Tachometer replacement thoughts

    I did not see that tach w/inset fuel gauge on LMC's site, just their kit's with separate fuel gauge.
  7. mtbadbob

    Power window harness

    I replaced my drivers door harness with the door on and it wasn't too bad. A rachet wrench is the way to go to get harness boot off. I just split the grommet at the kick panel so I wouldn't have to remove wires from the connectors under the dash.
  8. mtbadbob

    Tachometer replacement thoughts

    I like it! Where is it from???
  9. mtbadbob

    Window Felt Replacement

    I measured & double checked mine again, there is definitely some type of cladding on there. They measure about 1/32nd different, and I can actually see it on the drivers side that it's slightly loose and I can see the metal behind it where it wraps around toward the window. I'm almost thinking...
  10. mtbadbob

    1987 Chevrolet 350 tbi high idle

    I don't think there is a sending unit made that doesn't seep oil out of it. My Subie BRAT has the same issue after replacing it with a new one several years back.
  11. mtbadbob

    Window Felt Replacement

    I'm going to measure mine, but I'm pretty sure the drivers window that is black is wider than the rusty metal one on the passenger side. I could be wrong, but I've examined them pretty close and am sure there is a thin piece of cladding of some sort. It always seems like the passenger side is...
  12. mtbadbob

    Stock Window Trim 87 Silverado

    The chrome trim is available on Ebay for about 1/2 the price as the supply houses. Probably the EXACT same stuff...
  13. mtbadbob

    Window Felt Replacement

    If you look closely, there is a thin metal cladding both inside & out over the top of the steel. I think it's actually aluminum, maybe plastic??? They are all mostly a bit rusty beneath this thin cladding, and without the cladding they are a bit thinner also.
  14. mtbadbob

    Window Felt Replacement

    Yeah, I think every window is a bit different. I left mine outside the door frame a bit, just barely tucked into the channel, and when the window shut it pushed it up into the frame more, so I figured it would settle into place where the window tracked. I finally got my wing window seals locked...
  15. mtbadbob

    Window Felt Replacement

    I could, but it's a bit of a different dimension without the cladding on it, it just looks skinny!
  16. mtbadbob

    Cruise Control Module location

    Bless you, SIR!
  17. mtbadbob

    Cruise Control Module location

    I'm trying to find out exactly where the cruise module mounts on my '87??? I cannot find it in a Haynes manual, the factory wiring manual, nor on this site unless I just missed it.
  18. mtbadbob

    87 engine harness

    I may be able to get you one at a local bone yard, I can check tomorrow as I'm headed there.
  19. mtbadbob

    Window Felt Replacement

    I also had to change my drivers door motor after the new felts. I bought a pair off ebay for like $58 with a 5 year warranty. I haven't done the passenger door yet as I've been trying to locate a wing window that has the black metal cladding on the divider bar as mine is bare, rusted metal. I've...
  20. mtbadbob

    New in PNW

    Welcome from Montana! Nice truck, PLEASE LEAVE IT AS IS!!! :)
  21. mtbadbob

    cheap-ish options for my 86

    Blocking the exhaust cross over will probably hurt the performance. There is a science behind cross overs, 2 into 1 exhaust systems on almost every combustion engine made. That is why the engineers install them from the factory. A higher flowing muffler & tailpipe will be more advantageous to...
  22. mtbadbob

    Can we be honest people?

    I LOVE Vegas! Now, the Chevette was another story!! Sorry, this should have said "Vega's":laughing1:
  23. mtbadbob

    CLEAN 80s K10 in Seattle for sale

    Back in '89 when I bought my SS, the GN's were essential the same price. I remember them being about $3,800-$4,200 all day long. I just didn't want a V-6 and thought the Monte's looked better. I wish I would have bought 3 Buicks now!
  24. mtbadbob

    CLEAN 80s K10 in Seattle for sale

    No car had the body lines of the Monte, that was my big attraction! In fact, I still want an '88 Aerocoupe, T-top, buckets car.
View older results

Latest posts

Forum statistics

Threads
48,401
Posts
1,066,576
Members
42,780
Latest member
blue10
Top