Search results

  1. Bronze Knight

    WTB Big Block AC brackets for A6 compressor.

    Never mind I got them off of Craigslist. Was $125 shipped. No did not have all the bolts but i dug around my box of bolts and got it mocked up. As I expected the rear lower bracket does not fit with the heddders on and the heads themselves are missing a boss (the rear most one above cylinder 3)...
  2. Bronze Knight

    Stumped on oil leak

    Well, I made a minor change but it seems to have fixed the issue. The valve covers I got have a 1-inch hole for a PCV vent. It would seem that 1'' filters are a bit less common, now you can get them on Amazon but I didn't do that. I went down to the auto parts store and got a 3/4'' filter...
  3. Bronze Knight

    Stumped on oil leak

    OK so I did the test again and I may have had the distributor clocked wrong yesterday. I also figured out a better setup for air fittings using the adaptor off the compression tester, a union, an air fitting, and hose clamps. Anyhow for today it would simply pop when I took the hose off but no...
  4. Bronze Knight

    Stumped on oil leak

    Yep, that's what I did. The roter cap was pointing at the vacuum advance which is where #3 is at I rigged up an air hose with some rubber line and the blow gun on the air compressor with some hose clamps and after I got it jammed into the spark plug just right I was getting air out the carb...
  5. Bronze Knight

    Stumped on oil leak

    Assuming I did this correctly. I got a good bit of air out of the Carb.
  6. Bronze Knight

    Stumped on oil leak

    .... Spoke too soon. I was feeling good about the truck so I drove it to work on a Friday a week or two ago. Everything was good on the way into work. But on the way home at every stoplight I was getting a small oil smoke cloud. Made it home thankfully but when I looked in the hood the oil...
  7. Bronze Knight

    Scores from DIY Parts Yards, Pull A Part, U Pull It etc

    Got a few things the other day. Jeep steering shaft for the mod. Throttle and hood cables, exhaust heat shield 9though sadly it doesn’t fit my crewcab) Coolent overflow bottle, and a nice Pintle/2 5/16 combo hitch.
  8. Bronze Knight

    Stumped on oil leak

    I just wanted to thank everyone here. I got everything back together last week and test drove it and I think this problem is done at last. I’ve taken it around the neberhood a few times and took the wife out to get ice cream yesterday. No leaks. There is more to do to the truck but at least I...
  9. Bronze Knight

    Stumped on oil leak

    Yep It wasn't in the way. I got the oil pump done and put the pan and timing cover back on. Hopefully tomorrow I'll get it all back together.
  10. Bronze Knight

    Stumped on oil leak

    It’s raining here which is not ideal. And I pulled a muscle in my back last weekend still getting over that. But I wanted to get something done today so I drained the oil and removed the pan. Looks like the plastic sleeve on the oil pump shaft is AWOL pump itself looks fine but I’m going to put...
  11. Bronze Knight

    1985 k30 starter

    My truck is quite similar. 1985 K30 with a 454 big block with headers, stock height and stock tires. However I can get my starter in and out no problem. Got any pictures?
  12. Bronze Knight

    Burning hei coils

    Isn't there a thing where if the Tach signal wire gets grounded it'll burn the coil out? May be worth checking the whole run of the Tach signal wire, or at least both ends.
  13. Bronze Knight

    Dually guys, need your opinions!

    A quick Google search and I found a few. I got worried because I'll need to get a driver-side one at some point, I just haven't had the money for it yet. WARNING: I've never ordered from these places and I have no idea of their quality...
  14. Bronze Knight

    Stumped on oil leak

    I was joking about the cork gasket guys lol. I have a one-piece oil pan gasket on there now. However, I have another one coming because the RTV is in the gasket now and even if I dig it all out I'm not willing to do this AGAIN so I'll use a fresh gasket. I don't think i need the Sleave on the...
  15. Bronze Knight

    Stumped on oil leak

    Pulled the Harmonic Balancer. Not sure what to think now. The bottom of the oil pan gasket looks like it was pushed in a little bit in a few different areas. This may have been a contributing factor. Then on the timing cover itself a couple of the bolt holes look stretched/ not flat. Oil could...
  16. Bronze Knight

    WTB Big Block AC brackets for A6 compressor.

    Wanted AC brackets for the A6 compressor to mount it to the 454 Big block. I know it's an old compressor and there are better options out there, but I'm trying to do this on the cheap (less than $1000) and I already have an A6 compressor and hoses for it. But I need brackets. From my...
    • Bronze Knight
    • Thread
    • a6 compressor ac compressor brackets wtb
    • Replies: 1
    • Forum: Wanted
  17. Bronze Knight

    What have you done to your square lately??

    I may try the hose and ball bearing thing. Going to give these a shot first apparently the temperature ratings for these are written a little misleading. When they say 400 degrees they mean 400 degrees for a max of 5 minutes.
  18. Bronze Knight

    What have you done to your square lately??

    Took care of another little issue today the vacuum plugs on my carburetor keep drying out and cracking so I finally got some silicone one’s supposedly rated for high temperature. Will have to wait and see if that’s true.
  19. Bronze Knight

    Stumped on oil leak

    It was a reasonable temperature outside after the sun went down so I started prep for doing the timeing cover gaskets. Took me a little less than 2 hours. I’ll have to rent a harmonic balancer puller tomorrow.
  20. Bronze Knight

    What have you done to your square lately??

    Added some stickers (actually a thin aluminum plate) to the valve covers. Some days it’s nice to have the little victories when battling the oil leaks. :Big Laugh:
  21. Bronze Knight

    Stumped on oil leak

    I had just enough time for another test drive berofe the rain hit today and I think this has got to be coming from the timing cover. Again I probibly only went about a mile or so. So although its not much oil I'd rather not have to deal with this all the time. Oil pan has a Felpro one piece...
  22. Bronze Knight

    Scores from DIY Parts Yards, Pull A Part, U Pull It etc

    A quick run from the other day. Was very surprised I got both emblems off intact. Oh I also got cab light covers and gaskets but forgot to get a picture of them
  23. Bronze Knight

    Stumped on oil leak

    Ah I see, so it should be routed so that the PCV breather vents back into the carb intake to burn off/use up that oil vapor. I'll see what I can do to simulate that. But that's more of a long-term issue. For now, it's at least working.
  24. Bronze Knight

    Stumped on oil leak

    Hang on there. If I had money for that I'd have my beast on the road! :Big Laugh: I didn't get much done today, it was about 98 outside. I did manage to get it onto the driveway and pressure wash the engine bay/framerails/inner fenders I was careful, so I didn't get anything electronic wet...
  25. Bronze Knight

    Stumped on oil leak

    I see the fuel pressure regulator there. But how does that affect the PCV valve/vent?

Latest posts

Forum statistics

Threads
48,401
Posts
1,066,562
Members
42,779
Latest member
blue10
Top