Recent content by SmashBack
-
Who sells the best fitting dash pad. Time for a new one
I bought a couple different ones and settled on USA1. Seemed like a great one out of the box. Fit ended up being so-so. Needed a lot of trimming. A metal support thing came out from where I HAD to trim, top right of gauge bezel. Then I realized this thing is spray painted (aka dyed). Paint... -
AC DELCO, Dorman, or MOOG control arms?
Delco mostly from China, Dorman always. Moog always been good stuff, but these days you never know.- SmashBack
- Post #4
- Forum: Suspension, Steering & Brakes
-
New Seatbelts?
Tina King stuff looks good, but is she painting the plastic? Kind of looks that way, and in my experience painted plastic doesn't hold up well. -
Factory cruise control wiring diagram?
Awesome, thank you!!- SmashBack
- Post #3
- Forum: Electrical & Audio
-
Factory cruise control wiring diagram?
So my 79 had cruise control and I'm doing the LS swap thing. I can't for the life of me find a diagram or description of what these factory cruise control wires are doing. 3 coming down column, looks like one was connected to a switch like the brake switch and that jumpered over to an IGN+...- SmashBack
- Thread
- Replies: 3
- Forum: Electrical & Audio
-
New dash pad from Cheyenne Pickup
Yes it did finally arrive a couple of weeks ago. It looks incredible and is the right color. It's packed in the box but I will get some pics uploaded when I am able. -
How to cram the most exhaust in there
Maybe that was a little ambiguous. By dropped in a meant I installed it. The Tejas mounts raise the engine and trans vs other mounts. The only picture showing the trans/shaft angle is before it was shimmed up so yes it was bad in that picture.- SmashBack
- Post #11
- Forum: Engine & Performance
-
How to cram the most exhaust in there
Wow looks like 4x4 you have to be even more creative. Who'd think on a big ole truck that the exhaust routing would be so difficult! Yes, those are the Speed Engineering headers. I can't imagine using them with any mounts other than the Tejas with how low they'd hang (a lot like the Summit...- SmashBack
- Post #8
- Forum: Engine & Performance
-
How to cram the most exhaust in there
Routing both to one side is the same amount of effort IMO and I don't care for the two tips on one side. Must be some kind of OCD! I've seen wildly varying results from X-pipes but all the results I've seen are more than marginal at best. It would be great to compare side by side on my own...- SmashBack
- Post #4
- Forum: Engine & Performance
-
How to cram the most exhaust in there
So I've dropped the lq4/4l80e in my 79 Big 10 (longbed of course). Had a 5" aluminum driveshaft built. I've got drop hangers and shackles out back so about 4" drop and have CPP drop spindles with stock springs in front. About to build the exhaust with 2.5 inch piping. I was thinking I was...- SmashBack
- Thread
- Replies: 12
- Forum: Engine & Performance
-
New dash pad from Cheyenne Pickup
I ordered one from them on 7-16-18, looks like the status finally changed from processing to processed. Wasn't in a big rush and if it's a good product, it'll be worth the wait. -
Headers with Tejas Steelworks mounts?
Thanks guys. I've spoken with Scotty a few times, from what I recall he recommends the Hooker manifolds which cost more than some of these long tubes. I'm running a fresh 4l80e, Dirty Dingo cross member and I'm having a new aluminum driveshaft built. Should be pretty cool! I keep going back...- SmashBack
- Post #12
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Headers with Tejas Steelworks mounts?
Driver side is fine, pass side pipe (2.5") will be tight, may be ok but...- SmashBack
- Post #9
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Headers with Tejas Steelworks mounts?
Still trying to figure out if the Speed Engineering will fit. Might have to roll the dice and order them to find out. Picked up Schoenfeld at the local Summit so I can easily return those at least, if needed. They fit great, other than the funky pass side collector position. Points a little...- SmashBack
- Post #7
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
