Recent content by Jrgunn5150

  1. Jrgunn5150

    Can Anyone Help Me Identify My Vortec 6000 Engine?

    That cover is a Lq9 cover, but they fit any Gen 3 truck engine from 99-06 They way to tell is the block is cast front and rear with either a 4.8/5.3 or a 6.0. Then scope the piston to see if it's a flat top or not. Yes = LQ9 No = LQ4. But they all do burnouts and run way better than the old...
  2. Jrgunn5150

    Can you dig it.

    My wifes Olds 98, thing has 8-9 ash trays lol.
  3. Jrgunn5150

    Help finding the DRAC 1990 V1500 Suburban

    Yes, I always thought that was the DRAC lol.
  4. Jrgunn5150

    Help finding the DRAC 1990 V1500 Suburban

    What is this thing then?
  5. Jrgunn5150

    Help finding the DRAC 1990 V1500 Suburban

    I thought it was behind the cluster?
  6. Jrgunn5150

    Marine 502 into 1984 GMC 2500 454

    https://www.jegs.com/i/JEGS/555/601026/10002/-1
  7. Jrgunn5150

    Marine 502 into 1984 GMC 2500 454

    I don't know of any tall deck 502's. Everyone I've ever seen was 9.8" and used all standard Mark IV stuff. The caveats were they didn't have clutch ball provisions. Regardless, tall deck 8.1 and 8.8's fit fine anyway.
  8. Jrgunn5150

    What have you done to your square lately??

    I do a lot of engineering filaments, PPS, PA6, PA12. Not too many "prosumer" printers that will run them out of the box, it does very good at it with the AMS HT dryers. I'm even able to embed TPU, in the engineering filaments, this is TPU/PA6 CF
  9. Jrgunn5150

    What have you done to your square lately??

    You can just break files into pieces. I have 2 Bambu P1S printers and a Bambu H2D, but nothing fancy is required for this. For this, as a mock up, I just super glue it together, it's not a functional or structural piece. In real life time, it'll take about a week, probably 40 or so hours...
  10. Jrgunn5150

    What have you done to your square lately??

    This is actually for my 4runner, but I'm pretty close to having a mock up LS block printed.
  11. Jrgunn5150

    What have you done to your square lately??

    Not much, spent part of the weekend fixing the water in my barn to find I have next to no pressure and I screwed it up somehow. Did get the brake pedal assembly and master painted, my donor cab definitely sat in water for some time lol. Didn't get to get it installed because I had to go empty...
  12. Jrgunn5150

    Eldorado Industries G30

    These are the coolest, I love the van conversions.
  13. Jrgunn5150

    unSquare K5 Floor Repair DIAMOND PLATE fabricated supports

    Idk, I don't see them move all that much really. Not considering how much adjustment there is in the panels and body mounts anyway. If it were me, on a K5, I'd probably take the top off, and lift from the bed. Get any bow out of the fender/door/cowl area, have that all line up and equal, then...
  14. Jrgunn5150

    1990 Suburban Master Cylinder Upgrade

    My C10 is a GMT800 Tahoe master with an S10 reservoir. Has rear discs on a Ford 9.75 axle.
  15. Jrgunn5150

    1978 C20 5.3 swap

    With Speed Engineering long tubes, the remainder of the exhaust is a perfectly straight shot to the axle if you're using one of the aftermarket dual hump crossmembers.
See more

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,168
Members
43,335
Latest member
Sierra_87
Top