Recent content by Jason Reed
-
1974 Chevrolet C10 Stepside Build....
my only reasoning was this builder has had expierience and success on the Fi-TECHs. But, as you mentioned, I’ve heard good things about all (3). Fi-Tech, Holley & Edelbrock- Jason Reed
- Post #116
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Also, I think earlier in this build thread, I shared a photo of what the engine would resemble, but after some more black accents, I decided to do a black engine with some chrome and Orange valve covers/air cleaner. So this is the 383 Stroker I’ll start with from a base. It looks great. - Jason- Jason Reed
- Post #114
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
I went with the same, 700R, 4-10's and then doing a 383 w/ Fi-Tech. Should come out clean, I hope. - Jason- Jason Reed
- Post #113
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Now that’s good news. Thanks @curse -Jason- Jason Reed
- Post #111
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Thank you- Been a process. Lol -Jason- Jason Reed
- Post #110
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Besides the motor and trans, all I have left are some little issues here and there and the installation of the Vintage A/C. Hopefully get back on it in a couple of weeks or so. -Jason- Jason Reed
- Post #107
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
So about a month ago, I was able to finish the bed. Used the Mar-K oak bed kit, which turned out great.- Jason Reed
- Post #106
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
@LoStep, what’s happening? Yes, I have been super busy with work and honestly just forgot to post where I’m at. I’ll work on some pics and updates here in a bit. -Jason- Jason Reed
- Post #105
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Boy- I hope that’s not the case. Lol. I purchased a 2” drop cross member to run. I assume that gives the allotted clearance. Have not test fit yet. Now I’m nervous. :)- Jason Reed
- Post #103
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
HaHa. I got the garage, she gets the house.- Jason Reed
- Post #101
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Went with a simple Kicker Audio setup as well - Jason- Jason Reed
- Post #97
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Well, I’ve almost got to a point where I’ve done everything I can here at the house. It’s pretty much ready to head back to the shop to get the bed assembled and bolted on. Coming along well. Interior turned out great. All new glass, rubber, door panels, trim. I’m really happy with the...- Jason Reed
- Post #96
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Got back on the C10 this morning early. Put about 7 hours into it. Finished all the stereo and wiring, installed the old school loop carpet (light gray), got the seat in and really liked how these door seal covers turned out from LMC truck. Good progress today. Jason-- Jason Reed
- Post #94
- Forum: Tech Discussion
-
1974 Chevrolet C10 Stepside Build....
Got back on the C10 this weekend. Got the steering column in, down to the steering box. Put in some nice Kicker kick panels and started the wiring harness. - Jason- Jason Reed
- Post #93
- Forum: Tech Discussion
-
