Search results

  1. D

    Carb help

    Ok I have an 80 k10 350 motor that was rwbuilt over 5 year ago. Most likely 10yr. Owner before me said he rebuild it out a mild cam in and bored it .30 over I believe. No paperwork but doing a compression test they were all at 145-150. So would a holly 650cfm work or would an 600cfm work? I...
  2. D

    New Vacuum lines

    Ok going to be running new vacuum lines for the heat and stuff and would like to know if anyone has a diagram of what num go to what vacuum line for the vacuum module. I already found one that shows what and we're all the lines to and stuff but I do not know what vacuum lines go were on the module.
  3. D

    Anybody use these headlights?

    If anyone has how were they? Any good, and do they out out more light than/better light pattern than stock sealed beams?
  4. D

    Lift kit swapping

    Can a 1980 k10 4in lift work on a k5 blazer? If so what years would it work on and would it still be 4in or would it be higher or lower?
  5. D

    205 tcase help!!!

    Ok my tcase is leaking at the front output I already found the one seal I would need that is round but I need to know part numbers and names for the second one. It pretty much looks like a carb gasket that goes between the carb and the intake. Any info/help would be greatly appreciated.
  6. D

    4in and 35s lets see them

    If anyone has a k5 on 35s with a 4in lift post them up. Also would like to see the size comparison as to how big it sits.
  7. D

    Which do you prefer??

    Ok which do you prefer and why? K5 blazer 6in lift with 37s or k30 6in lift and 37s? What would you rather have for a weekend warrior but be your dd?
  8. D

    Heater help!!!

    Does anyone know we're to get the vacuum lines that run from the control box the the heater box and were to get the rubber part that holds all the lines that go over all the little nipples on control unit that selected what door gets the vacuum?
  9. D

    Ac/heat vacuum lines

    Ok I need some help. Was having issues with my defrost so I took the dash apart found the issue. Problem is I need the vacuum lines that run behinds the dash that go from the climate control to all the doors and stuff on the heater box. Also I need the rubber piece that's attaches the lines to...
  10. D

    Gearing with rpm rang

    I was on the freeway doing about 70 and my rpm's were a hair under to right in 3k. Truck is a 80 Chevy 350 with 31 by 10.50 tires on stock rally rims. Any idea what gearing would be in the rear end? Would 35 by 12.50 help lower that rpm down and make it more happy at highway speeds or would it...
  11. D

    Lockers?

    Ok I was wonder does anyone have any experience with the eaton tru track locker? Any good for off-roading? I drive manly street but want something that can be better than an open diff when off-roading not rock crawling just back woods off-roading. Don't rlly want to spend a ton and get an air...
  12. D

    Looking for wheels

    I'm having a hard time finding wheels. Looking for 15 8in wide with a 4.5 bs. Anyone know of any sites that have some?
  13. D

    Lift kits help

    With a 4in rough country lift kit do I need a sway bar drop bracket or no? Also I know you can run 35 12.50 on 15in rim will a 4in back spacing be able to clear without rubbing?
  14. D

    Tire fitment

    There is probably been ask a million times but truck currently has 31 by 10.50 on stock 15s. Could I run 32 by 11.50 on the stock 15s? Without rubbing? Truck has no lift kit or anything.
  15. D

    Spring help

    My front leaf springs are negative arched so it rides like a tank and was wondering should I just get new front leaf springs or find a spring shop to re arch them and put an add a leaf?
  16. D

    Please Seat belt help!!

    Ok I have a 1980 Chevy k10. it has bucket seats with the stock 3 point sealt belts. The problem is when my girlfriend is siting in the passenger seat the belt cuts into her neck/throat. To the point that if we got into a wreck would most likely snap her neck(yes she is short lol). Anyway tho I...
  17. D

    Rusty/dirty frame

    My 80 k10 Frame has surface rust on it and the paint that was on or whatever was on it is all peeling off. Rust has no gone threw nor made rust holes. But I was wondering is it still worth sanding it down to repair it or does it need to be sandblasted? I can post pics tomorrow afternoon if those...
  18. D

    Body panel fitment

    I went to my local junkyard and found a hand full of old Chevys,one k5 and 2 Chevy suburban. My question is what body panels from those will fit a 1980 Chevy k10. If they would what years should I be looking at? I mainly need a hood, front fenders and doors.
  19. D

    Shift Indicator for Z71 Column

    Got a question bought a 1989 Chevy k10 auto trans and the guy before me installed a z21 steering Coloum and has a string and screw for the gear selector if I get that metal bracket will the gear selector work as it should? Because I have no bracket and were it goes I just have the screw
  20. D

    Gauge help!!!!

    I just picked up a 1980 Chevy k10 4x4 auto the speedo fuel gauge and cluster lights don't work the fuel gauge tho work buts it's on we're it should be off its straight down and on it goes to 3 O'clock any idea on what this could be related to on this stuff now working? Also my fuse box does not...

Latest posts

Forum statistics

Threads
42,235
Posts
911,873
Members
33,739
Latest member
michaelmarine53
Top