Search results

  1. brianhannon

    4in and 35s lets see them

    My stepdad's 75 with 4in lift and 35's sitting next to my 2wd 75. haha
  2. brianhannon

    Performance question

    And as far as the vacuum gauge goes, just route the line to wherever your advance line would go. I think at idle manifold vacuum should run above 18 or 20 hg.. Personally I would first check to make sure you have a steady flow of fuel, just because that's easy to start with (no filter issues if...
  3. brianhannon

    Performance question

    Possible fuel delivery issues? Does it still have the old Quadrajet carb?
  4. brianhannon

    Emblem Help

    Those emblems are original. You may have to go to a different website and search around. Or pick some up at a local junkyard!
  5. brianhannon

    8 Lug Vs. 5 Lug 2WD?

    Thanks!
  6. brianhannon

    8 Lug Vs. 5 Lug 2WD?

    Hi, I am restoring my grandfather's 75 2WD C10. The frame is completely rotted through and I found a decent frame from a 73 at a local junkyard. The 73 is a 2WD 8 lug. Is the frame the same from 5 to 8 lug? I'm assuming I can just swap out front suspension components. Thanks, Brian
  7. brianhannon

    Where can I find 10" wide 5 on 5 15" Aluminum Slots??

    Looking for 5 on 5 pattern 15" Aluminum slots that are at least 10" wide. Going to pick up a nice set of M/T Sportsman Pros to throw on the back of my 75. Where the heck can I find decently priced slots? I have American Racing slots already, so I'd like to just grab two wider wheels for the...
  8. brianhannon

    Questions about 383

    Look at the harmonic balancer. The 400 crank balancer has a large cutout in the side (an indent sort of thing) and a 350 balancer just has the small tick mark for timing. Unless the engine was built using internal balancing, you should have a 400 balancer. I know more and more people are doing...
  9. brianhannon

    Best place to buy body repair panels? (Rockers, cab floor, corners, etc.)

    Hey fellas, I just purchased an '85 cab to replace the too far gone '75 I have now. I'm in the the midst of doing some body work on this "new" cab and I decided to do new inner/outer rockers, cab corners, and a drivers floor pan. Where's the best place to buy this stuff for a decent price and...
  10. brianhannon

    Best rear locker/ best price?

    Thanks for the advice!
  11. brianhannon

    Best rear locker/ best price?

    I was planning on using the same rear. I'm not one to hammer into it too hard but I'd like both wheels to be there on the occasion that I do
  12. brianhannon

    Best rear locker/ best price?

    Hey all, Looking into buying a locker. Tired of the open rear, I've got a built 383 and I need the power to the pavement! 3.42 10 bolt/ TH350.
  13. brianhannon

    what does a bad torque converter sound like?

    Maybe it could be a bad pump then? It sounds similar to a power steering pump that it going bad or is low on fluid
  14. brianhannon

    what does a bad torque converter sound like?

    So I have a stall converter in my 75 TH350 behind a 383. A few days ago I took off from a traffic light pretty fast and it started making thus whirring noise while moving slowly and a sort of grinding noise when at a stop in gear. Fluid looks fine. It also makes a whirring noise while in park...
  15. brianhannon

    Thinking about a 1" Body Lift - Thoughts

    That looks awesome! Suspension lift ftw haha:cheers:
  16. brianhannon

    Thinking about a 1" Body Lift - Thoughts

    You can do a suspension lift, just depends on how much you want to spend
  17. brianhannon

    Anybody know of a specific name for this shade of red??

    What shade of red is this???
  18. brianhannon

    Truck won't start

    Did you replace the solenoid when you replaced the starter as well?
  19. brianhannon

    Flat bed ideas

    Here's a few pics of my flatbed. Don't mind the burnout! lol:party36:
  20. brianhannon

    part

    It's part of the emissions system, possibly leaking because of condensation in exhaust? Is it coolant?
  21. brianhannon

    part

    Looks like some sort of a diaphragm or regulator, is the hose it's attached to a heater hose?
  22. brianhannon

    DIY Satin Black Paint Job

    Alright thanks!
  23. brianhannon

    1987 tbi stalls under load, idles rough when cold

    Nick, Didn't have any issues before? This just started after the valve work was done? Brian
  24. brianhannon

    DIY Satin Black Paint Job

    Hey Guys, Looking to refresh the truck with a satin black job. Anyone ever used Rustoleum 7777 and had a good turnout? Trying to get the best finish for a decent price. Thanks!
  25. brianhannon

    Beer keg gas tank

    I've always liked the look of a keg, but I might consider the tanks as well. I guess what I'm trying to do is just eliminate the ugly look of the factory tank underneath the truck and go with something more unique that would go well with the flatbed.

Latest posts

Forum statistics

Threads
42,126
Posts
909,669
Members
33,618
Latest member
1975K20
Top