Search results

  1. Charlie7985

    Blower motor won't turn off

    I recently rebuilt my entire a/c system. At first when a/c was running I had a constant fog horn type noise that appeared to be coming from the blower motor relay. I replaced the relay which was new and it would also do it intermittently. Replaced again with a different brand and would make the...
  2. Charlie7985

    Blower motor won't turn off

    I recently rebuilt my entire a/c system. At first when a/c was running I had a constant fog horn type noise that appeared to be coming from the blower motor relay. I replaced the relay which was new and it would also do it intermittently. Replaced again with a different brand and would make the...
  3. Charlie7985

    Humming From Relay

    I recently completed a rebuild of my a/c system that had missing components when I bought the truck. When the air was on, I noticed a loud humming noise coming from the blower motor relay. I got a new one and it did fine for a couple of days and then it started doing it too. Does anybody know if...
  4. Charlie7985

    Throttle Return Spring w/Idle Compensator

    I recently built a 350 with Edelbrock manifold and carburetor. Now I'm trying to get the A/C going. I can't figure out a good way to hookup the throttle return spring after I install the idle compensator for the A/C. Does anybody have a good setup for this?
  5. Charlie7985

    Which PAG Oil to Use

    It is the same as what you have in that picture, but it is silver instead of black. I have that same bracket setup too.
  6. Charlie7985

    Which PAG Oil to Use

    It is an A6 compressor
  7. Charlie7985

    Which PAG Oil to Use

    I recently bought one of the aftermarket A/C kits that has the compressor, evaporator, orifice tube, o-rings, and oil. It came with a bottle of Pag 150 oil, but it has this sticker on it. Does anybody know what I'm supposed to use?
  8. Charlie7985

    Master Cylinder Leak

    Finishing up a complete rebuild of a 79 C10. Installed new booster, master cylinder, lines, etc. The reservoir keeps leaking from the lid at the back and running down the booster and onto the frame. Even though the lid and gasket were new, I've replaced them and still the same thing. Any...
  9. Charlie7985

    Speedometer Gear Moving on Shaft

    I have a TH350 transmission that was recently rebuilt. Since then the plastic gear that goes around the shaft in the tail housing that is held on by a metal clip and engages the speedometer gear has slid down the shaft twice and caused the speedometer to stop working. Has anybody run into this...
  10. Charlie7985

    Air blowing out dash vents even when defrost or heat is selected?

    I had this same problem and it was from the actuator that controlled that door having a slight leak that kept it from closing the door all the way. You can test it by pulling the rubber piece where all of the vacuum lines connect to the back of the dash controls off. Then plug a hand held vacuum...
  11. Charlie7985

    Dome light housing reads resistance

    Were you able to find one that wasn't and if so where?
  12. Charlie7985

    Dome light housing reads resistance

    I recently had an issue with my interior lights not shutting off when the doors were closed. I understand this is a constant power circuit with a ground created by the door jamb switches and I was able to isolate the problem to the dome light. This is a new dome light housing, as there was not...
  13. Charlie7985

    The vendor parts that work, parts that don't.

    Dash panel molding I paid $80 for from Classic Parts of America. Silver accent line rubbed off on my hands and smeared on my dash while I was installing it. I had to use acetone to get all of the silver off the dash pad. Emailed customer service and they said sometimes you have to clear coat...
  14. Charlie7985

    Wiper motor turns continuously in the same direction

    Sorry for the late update. I ended up taking the wiper arms off so that I didn't have to deal with them binding up trying to go down through the cowl and I could see how the mechanism was operating. Noticed the they were turning down then up, instead of up then down. Removed the linkage from the...
  15. Charlie7985

    Wiper motor turns continuously in the same direction

    When I installed it the wipers just kept trying to go down past the point they were able to, even after I changed the position of the arm that bolts onto the motor shaft.
  16. Charlie7985

    Wiper motor turns continuously in the same direction

    My windshield wiper motor is turning continuously in the same direction instead of turning back and forth. I've changed out the motor and have a new switch. Any ideas?
  17. Charlie7985

    Different Turn Signal Speeds

    Thanks, I'll check that.
  18. Charlie7985

    Different Turn Signal Speeds

    My left turn signal seems to be blinking at normal speed and my right turn signal is significantly slower. I put a new flasher in and there has been no change. Anybody run into this before?
  19. Charlie7985

    Bed mount rubber spacers

    Does anybody know if these trucks had the square rubber washers between the bed and frame from the factory? The bed mounting kit I bought had them, but they raise my bed too high for the body line to match up. I'm thinking of taking them out, but bed cross members would be metal on metal with...
  20. Charlie7985

    Dome light wiring

    I have an issue with the light under the dash not turning off and the dome light not working at all. I have replaced the door jamb switches with no change.
  21. Charlie7985

    Rust and water in cylinder

    I've already gotten all the water out. What about the rust that is already there? Will it hurt anything if don't get it out?
  22. Charlie7985

    Rust and water in cylinder

    I had a motor sitting outside on a chassis for a couple of months while the body was being painted. I had it covered with a tarp that was ripped and blown off during a storm ome night. I thought it was fine, but then I found water inside my intake and ine if the cylinders. Has anybody run into...
  23. Charlie7985

    Door Window Weatherstripping

    I'm not having an issue with window thickness, it's finding one that will fit properly in the door frame.
  24. Charlie7985

    Door Window Weatherstripping

    I know there is probably another thread out there on this, but I couldn’t find an answer. Does anybody know where I can get some door window weatherstripping that actually fits my damn doors?
  25. Charlie7985

    Wiper Arm Spring Replacement

    I recently removed my wiper arms, cleaned them up and refinished them. I also bought some new springs to replace the old rusted ones. Does anyone know how to get them back on or if there is a tool for this?

Latest posts

Forum statistics

Threads
42,292
Posts
913,157
Members
33,792
Latest member
Twistedwhisky
Top