Recent content by plugugly

  1. P

    Air in fuel lines after sitting over night on 6.2

    any idea what O-rings I need? Both the bleeders on it look wet, I should probably replace those too?
  2. P

    Air in fuel lines after sitting over night on 6.2

    i do have air in my clear hose that goes away once running again. i do have the brick filter. was thinking about replacing with a spin on. trying to find more info about that. fp is fuel pump? ip is injection pump?
  3. P

    Air in fuel lines after sitting over night on 6.2

    suddenly, the last two nights, my sons blazer has been getting air trapped in lines wen sitting overnight. I can bleed and get it started, and it will be fine again till it sits overnight. Anyone have similar issue that may be able to save me some time from tracing the leak down? I guess its...
  4. P

    factory bumper carriage bolts?

    anyone know offhand if its 1/2-13 or metric? ecklers and LMC dont tell what size they are. Mine are rusted and crappy. The 1/2 die wont go on very well, so Im leaning toward metric. Was going to order new stainless ones from mcmaster
  5. P

    AC redo after sitting disconnected for a long time

    thank you. Figure I need to see if the clutch even works, check all wiring, etc. Is there any indication if the system has pressure other than releasing thru a shraeder valve? There is no belt around pump, dont know why. Dont know if PO changed anything on the refrigerant side. I know...
  6. P

    AC redo after sitting disconnected for a long time

    the 87 6.2 we bought has not had the AC working since long before we bought it I believe. Is there a simpletons version of troubleshooting the AC and where to check, verify etc anywhere on here? Like AC 101 for *********? I dont know squat about AC's but would like to try and get this thing...
  7. P

    ORD front lift springs caster correction needed?

    swapping some super stiff front 4" springs for a set of used ORD 4". Planned on reusing the degree shims that were in there, but the center pin hole is oversized and wont work with the new center pins I bought. (Old pack had a very long head that stuck thru the shims. DO ORD springs come with...
  8. P

    4 Inch Lift kits

    Hey Stephen, Been meaning to call your shop and ask. Id like to run a set of your front 4" springs but would be interested in running a stockish 63/4" rear spring on a shackle flip to level it out. (yes Im aware the front hanger needs to be moved, i did cosider inboarding and moving under the...
  9. P

    Superduty Dana 60 into 86 2wd squarebody chevy

    disregard, I apologize. I missed that you were using the early superduty stuff
  10. P

    head light switch not releasing with button

    Anyone every have the button stop working on the headlight switch? Im wiring stereo stuff and need to remove the gauge bezel again, however, the little button on the head light switch to release the pull lever is not functioning apparently. I cannot get the damn thing out. EDIT: nevermind, Im...
  11. P

    Rock slider attachments

    thanks. I was more concerned about years of wheeling and landing on rocks. Best I can tell, there are no sleeves going thru the boxed area correct? Any issues with crushing the box over time or the holes egging out?
  12. P

    Rock slider attachments

    A lot of the links for rock sliders are dead now. I see DIY and a fw others use the body channel to mount to. Im sure Kurt makes good stuff, but Im curious if anyone has had bad results from mounting to the boxed area over time. Was originally planning on mounting to frame, but then they will...
  13. P

    steering column shift collar orientation?

    putting my dash back together. I understand how the shift indicator clips onto the collar on the column. my collar has three "clips? that presses into the main column neck. Do they need to be oriented one way or another when pressed inside the column? I can get everything mounted up, but as...
  14. P

    interior paint codes?

    anyone have to codes for the dark blue and white? Was hoping to have a local shop mix it up for me.
  15. P

    Ecklers eurathane dash pad?

    anyone have experience with this version? Its currently for sale and not a whole lot more than a coverlay set up. https://www.ecklers.com/chevy-and-gmc-truck-urethane-dash-pad-assembly-1981-1987-61-336607-1.html#customer_q_and_a
See more

Latest posts

Forum statistics

Threads
42,249
Posts
912,061
Members
33,749
Latest member
630erik1
Top