Recent content by 83chummins

  1. 83chummins

    C&C swap from 14bolt rear headaches

    Last steps to a money maker fellas!! Almoat there! Sent from my LGMP260 using Tapatalk
  2. 83chummins

    C&C swap from 14bolt rear headaches

    Veiw from the rear Sent from my LGMP260 using Tapatalk
  3. 83chummins

    C&C swap from 14bolt rear headaches

    Dually swap Sent from my LGMP260 using Tapatalk
  4. 83chummins

    C&C swap from 14bolt rear headaches

    A while later with all my fingers and toes still attached. she is almost ready to make some dollhairs Sent from my LGMP260 using Tapatalk
  5. 83chummins

    Procar touring seat upgrade!!!

    I almost went the same route but me and the ol lady decided on az instead. I only use mine in BLM or NF otherwise my smart level hangs there with my hood. Sent from my QTASUN1 using Tapatalk
  6. 83chummins

    Procar touring seat upgrade!!!

    @ apeman Well I'm 6'1 190 and fit perfect. That being said, I would say get a smaller wheel and modify the seat mount you might gain a bit of clearance. I would say u might go with the low back procar seats ; yes the procar touring model seats do put you higher up than the bench I'll take some...
  7. 83chummins

    C&C swap from 14bolt rear headaches

    Question for setting pinion angle. The whole Idea is to get the pinions matched up parallel for correct operating angle? I was goin to go off the what's on the truck but checking it today I found that it 6deg difference from the slip yoke on the 205 and the pinion on the diff. Driving pinion 3...
  8. 83chummins

    C&C swap from 14bolt rear headaches

    So i finally said screw it im goin to move the perch inside 1 1/2" made my own new perch Sent from my LGMP260 using Tapatalk
  9. 83chummins

    C&C swap from 14bolt rear headaches

    Im goin to try o find a set of k30 srw hubs Sent from my LGMP260 using Tapatalk
  10. 83chummins

    C&C swap from 14bolt rear headaches

    Forgot the pic Sent from my LGMP260 using Tapatalk
  11. 83chummins

    C&C swap from 14bolt rear headaches

    Here we go for round two swing and a misssss dissassembled everything from dually c&c plan was this morning to take srw hub from 14ff off the truck and put it on the drw drum, takeoff the backing plate plate with brakes from drw cc and swap that over to the srw 14ff axle on the truck then add...
  12. 83chummins

    C&C swap from 14bolt rear headaches

    I don't wanna give up that easy man if I do this once with a little extra effort and planning it should work out and be worth it. I have the back up plan already from the BSF videos if my back is against the wall Sent from my QTASUN1 using Tapatalk
  13. 83chummins

    C&C swap from 14bolt rear headaches

    Alright so I'm not so sure the 1 ton SRW hub looking at the pic from (craig85) will work with with my 2 in spacers run outta spindle housing. I think I'm going to fabricate my own spring hangers do a shackle flip to drop out my 4in block as well it's already bagged so I think it will work out...
  14. 83chummins

    C&C swap from 14bolt rear headaches

    I dont mind throwin on k 30 spring hangers. And hmmm i thought about doin the disk conversion on the cc drw axle but not on the srw 3/4 ton.. Sent from my LGMP260 using Tapatalk
  15. 83chummins

    C&C swap from 14bolt rear headaches

    You mean these two spacers!!! I got em just in case things just plain dont work out. As for the srw 3/4 ton drum hub assembly the dually wont fit on it becuase of the straight lip before the hub instead of the beveled end like the drw drum hub assembly. Sent from my LGMP260 using Tapatalk
See more

Latest posts

Forum statistics

Threads
42,156
Posts
910,246
Members
33,652
Latest member
strokedK15
Top