Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
yevgenievich
Full Access Member
·
From
Texas
Joined
Mar 1, 2014
Last seen
Yesterday at 11:01 PM
Posts
4,794
Reaction score
3,332
Points
113
Find
Find content
Find all content by yevgenievich
Find all threads by yevgenievich
Latest activity
Postings
About
yevgenievich
replied to the thread
Moved to FB 1987 C20 parts truck. Near Fort Worth
.
How is the cab rust? Could really use to get a cab fixed on a friend's truck, but not sure when we could make it. About 3.5hr drive
May 7, 2024
yevgenievich
replied to the thread
Adding a headrest to a bench seat
.
A set in post 15 was previously used successfully. Available for sale if anyone wants to try, although blue is not axact match...
May 5, 2024
yevgenievich
replied to the thread
8.1 Vortec VS 383 Stroker VS 6.0 Iron LS
.
There are aftermarket mpfi intakes for a bbc that will run on 411 ecu if going away from l29 intake manifold. Or 8.1l with stock intake...
Apr 11, 2024
yevgenievich
replied to the thread
8.1 Vortec VS 383 Stroker VS 6.0 Iron LS
.
Gen6 454 would be good to consider as well. Big block or 383 will have better low end torque than a stock 6.0 ls
Apr 4, 2024
yevgenievich
replied to the thread
Adding a headrest to a bench seat
.
Head rests on GMT 400 bench work for the height
Apr 1, 2024
yevgenievich
replied to the thread
Catch Cans
.
That is 8.0l bbc with brodix race rite heads. I am also running a pcv valve with check valve from a turbo solstice. Were left over...
Mar 31, 2024
yevgenievich
replied to the thread
Catch Cans
.
I am running efi with maf. After the maf, line goes to one of the valve covers then goes out from other side with pcv valve in to a...
Mar 30, 2024
yevgenievich
replied to the thread
Catch Cans
.
Depends on the engine. I get some oil in the catch can. On burban mostly because valve covers are spliced from two and relatively large...
Mar 30, 2024
yevgenievich
replied to the thread
Catch Cans
.
Running one connected on output of pcv valve.
Mar 29, 2024
yevgenievich
replied to the thread
stealth
.
Forced ventilation and existing dust on the shelves. Everything that I cared for was covered, the rest did not realy get any overspray...
Mar 28, 2024
yevgenievich
replied to the thread
stealth
.
Had to recently replace clutch slave and a line as it started to leak. Then get hit and run while parked. It is pretty evident who did...
Mar 28, 2024
yevgenievich
replied to the thread
Transmission Upgrade?
.
4l80e would be the likely choice. 6 speed would allow to have steeper 1st gear for quick take off. I was getting about 12mpg with gen6...
Mar 27, 2024
yevgenievich
replied to the thread
Under-pad replacement suggestions?
.
I used regular carpet jute for houses before. Seem to work fine
Mar 8, 2024
yevgenievich
replied to the thread
89 Trans Am
.
Finally getting some finishing pieces on interior. New rear 6x9 speakers installed, new sail speaker covers, put pillar trim back on...
Mar 7, 2024
yevgenievich
replied to the thread
Train wreck
.
Sunroof service.
Mar 5, 2024
Loading…
Loading…
Latest posts
New guy here from Wyoming.
Latest: JamesSam
50 minutes ago
Introduction
Newbie
Latest: JamesSam
52 minutes ago
Introduction
I
Radiator condenser combo.
Latest: idahovette
Today at 1:43 AM
Engine & Performance
Intake plenum gaskets
Latest: DoubleDingo
Today at 12:53 AM
Tech Discussion
rebuilt sbc Oil pressure
Latest: Matt69olds
Yesterday at 11:40 PM
Engine & Performance
Forum statistics
Threads
42,342
Posts
914,018
Members
33,844
Latest member
aaron06
Members
Top