Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
GTX63
Full Access Member
·
From
Tennessee
Joined
Nov 27, 2022
Last seen
Today at 7:35 AM
Posts
755
Reaction score
3,056
Points
93
Find
Find content
Find all content by GTX63
Find all threads by GTX63
Latest activity
Postings
About
GTX63
replied to the thread
Removed heater box from '81 C10 to replace the heater core, easier than I expected.
.
No comparison to pulling the heater core in a squarebody vs say a late model GM truck.
Thursday at 4:24 PM
GTX63
replied to the thread
1985 K10 Wiper Issues
.
Interesting. I wonder if a sliding dimmer switch would give it the delay feature.
Thursday at 7:02 AM
GTX63
replied to the thread
Fuel guage bounces?
.
Most of the squarebodies pre tbi had resistors on the back of the gauge and they can vary over time. In this case we are talking...
May 9, 2024
GTX63
replied to the thread
83 K5 Blazer LS swap issue
.
Years ago I had a fuel pressure regulator fail and it flooded the cylinders with raw fuel, and yes, it was leaking out.
May 5, 2024
GTX63
replied to the thread
Suburban Rear vs Truck Rear
.
5 lug half ton 2wd drive 8.5" 10 bolt rear end Suburban rear axle is the same as a 5 lug half ton 2wd 8.5" 10 bolt C10 rear axle long or...
May 3, 2024
GTX63
replied to the thread
Fuel gauge
.
Takes about 15 minutes.
Apr 26, 2024
GTX63
replied to the thread
Where to get quadrajet rebuilt?
.
I also use Quadrajet Power for rebuild kits. They have always done me right. I rebuild my own. If you have never done one before, there...
Apr 25, 2024
GTX63
replied to the thread
Engine lift points
.
Yes, but based on experience I don't consider them optimal. A carb plate gives you better control and the ability to tilt the motor as...
Apr 25, 2024
GTX63
replied to the thread
low oil pressure
.
What manufacturer is recommending 5W30 for a Gen 1 small block? Not trying to be argumentative just curious.
Apr 21, 2024
GTX63
replied to the thread
Hood latch
.
Apr 21, 2024
GTX63
replied to the thread
Most affordable shipping for body panels?
.
I was at the C10 Nationals last year for just one example- the suppliers were there with motors, body panels, trim, interior parts...
Apr 20, 2024
GTX63
replied to the thread
Most affordable shipping for body panels?
.
You can also try hitting the car and truck shows over the summer. Many times at the larger events, you can find the dealers at a booth...
Apr 20, 2024
GTX63
replied to the thread
Trash my dash? And interior panel take offs?
.
Lots of trucks out there without any dash pad. There will be someone who might need a core for a cheap cover or to redo, so yes, it is...
Apr 19, 2024
Loading…
Loading…
Latest posts
I
Replace old pump or keep it?
Latest: idahovette
3 minutes ago
Suspension, Steering & Brakes
GMC-IH
Latest: dragstews
9 minutes ago
Other Vehicles
Scores from DIY Parts Yards, Pull A Part, U Pull It etc
Latest: SDJunkMan
18 minutes ago
Garage
Newbie
Latest: animal
Today at 9:52 AM
Introduction
Engine Stalling - Bad EVAP/Charcoal Canister?
Latest: 75gmck25
Today at 9:52 AM
Carb Fuel Systems
Forum statistics
Threads
42,344
Posts
914,042
Members
33,846
Latest member
JOD26
Members
Top