What have you done to your square lately??

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Out here in the garage, thinking about how to configure the Sniper 2 coolant sensor. The sensor is the wrong thread for the intake, and even then it wouldn’t play well with the thermostat housing angle.
You must be registered for see images attach

So I found this gem, and some t-bar clamps for the heater hose off the intake manifold. Not elegant but it will work, since the Brodix heads don’t have a coolant sensor bung.
You must be registered for see images attach

Then I got a hose barb for the PCV, for the front.

That’s as far as I’ll go for now, heading to PA and KY to visit friends and family early next week.

Isn't the coolant temp sensor NPT?
 

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
2,315
Reaction score
8,625
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
Isn't the coolant temp sensor NPT?
Yep and this one is as well.

Edit- if the receiving fitting isn’t, won’t the NPT seal into it anyway?
 
Last edited:

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
2,315
Reaction score
8,625
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
Never mind, the female threads are NPT. Phew! @bucket
You must be registered for see images attach
 

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Never mind, the female threads are NPT. Phew! @bucket
You must be registered for see images attach

I guess my statement was, the NPT sensor should thread into the NPT threads on the manifold. I've never seen an aftermarket manifold that didn't have NPT threads in the coolant ports.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
10,712
Reaction score
20,955
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
You could use a tee at the passenger side manifold port, long side of tee vertical, coolant temp sender blocks end of tee off.Side of tee to heater. I'd also explore drilling and tapping the manifold for another port or a thermostat housing with a port. Pic of thermostat spacer with ports and manifold drilled and tapped for 4 ports
 

Attachments

  • Screenshot_20261007_192237_Chrome.jpg
    Screenshot_20261007_192237_Chrome.jpg
    54.9 KB · Views: 24
  • Screenshot_20261007_192827_Google.jpg
    Screenshot_20261007_192827_Google.jpg
    104.1 KB · Views: 28
Last edited:

Camar068

Supporting Member
Air Force Supporting Member
Joined
Feb 5, 2014
Posts
5,113
Reaction score
5,118
Location
Kentucky
First Name
David
Truck Year
1986
Truck Model
K10/LM7 5.3/4L60e/np208/3.73/32"
Engine Size
10 yrs Air Force
Removed and rebuilt the heater box. Fabricated new vacuum lines and will be installing it in an attempt to get the hvac system functioning properly. After that, it is time to tackle the cluster
did you change the hard, small rigid line? Has always pissed me off.
 

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
2,315
Reaction score
8,625
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
I guess my statement was, the NPT sensor should thread into the NPT threads on the manifold. I've never seen an aftermarket manifold that didn't have NPT threads in the coolant ports.
It does have one 1/2” NPT, but it’s directly under the water neck and I’d like to keep the factory gauge as well.
 

ChuckN

Full Access Member
Joined
Nov 8, 2022
Posts
2,315
Reaction score
8,625
Location
Bellinham, WA
First Name
Chad
Truck Year
1981
Truck Model
C10
Engine Size
350
You could use a tee at the passenger side manifold port, long side of tee vertical, coolant temp sender blocks end of tee off.Side of tee to heater. I'd also explore drilling and tapping the manifold for another port or a thermostat housing with a port. Pic of thermostat spacer with ports and manifold drilled and tapped for
Thanks for bringing that spacer to my attention. I HAVE looked at those, but most of them don’t move the thermostat up, they just move the water neck up, and I want the sensor pre-thermostat. I can also angle it towards the back so it’s hidden a little, and it won’t be vertically mounted so I can’t accidentally smack the sensor when it’s sticking up like a sore thumb. I think that’s my solution.
 

shawn57nomad

Supporting Member
Supporting Member Navy
Joined
Jul 3, 2025
Posts
138
Reaction score
378
Location
Midwest
First Name
Shawn
Truck Year
1981
Truck Model
C10
Engine Size
250
You know that thing... one thought turns into another and....WHAM! You put it together then take something else apart! . ADHD for life!

Dash assembled (missing 4 clips GRRRRR), MIL done, Malwood clutch pedal done, heater hoses and bypass wired, core support/condenser/radiator aligned and remounted.....then decided to drop the dual tanks to install the New with 340lph pumps. Then a squirrel moment and pulled the seat to clean the floor and said HEY why not lay the new rubber flooring in! Not ideal at 58 degrees!
 

Attachments

  • KIMG20261007_224445137.JPG
    KIMG20261007_224445137.JPG
    124.5 KB · Views: 31

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
7,611
Reaction score
28,869
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
So y'all know our '76 shop truck I post about sometimes. 5+yrs ago I said I'd like to buff her out cuz she's basically been satin the whole time we've had her. Especially on the top surfaces. Well, I'd buffed my truck a couple weeks ago and was about to put the stuff away on Tuesday when I decided "lets buff Goldie before I put this stuff away". So that's been the project the last couple afternoons.

I did the driver's side first cuz it's still single stage. The side was shinier than the top, but it still brought the color out and gave a much better reflection
You must be registered for see images attach


This is the driver's bedside before and after
You must be registered for see images attach


The hood was AWFUL
You must be registered for see images attach


Same with the roof
You must be registered for see images attach


And the tailgate
You must be registered for see images attach
 

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
7,611
Reaction score
28,869
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
The pass side was always much shinier cuz it'd been repaired, repainted and clearcoated at some point in the past. We think granny or grampy wiped out a parking pole cuz the pass fender and door are full of bondo. You can see where the gas has stripped the clear off
You must be registered for see images attach


This is all I was using, just a single pass on most of the truck. 2 passes on a couple spots
You must be registered for see images attach


And a HF foam medium cut pad
You must be registered for see images attach

You must be registered for see images attach
 

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
7,611
Reaction score
28,869
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
Now she looks as good as she runs! I can't believe how good this came out for just a quick and dirty buff job. I'll work on getting her waxed today

You must be registered for see images attach



You must be registered for see images attach


You must be registered for see images attach


You must be registered for see images attach
 

Latest posts

Forum statistics

Threads
48,830
Posts
1,090,957
Members
44,119
Latest member
79TanSquare
Top