What did you fix on your daily, today?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
9,984
Reaction score
18,374
Location
The Right side of Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
^ I’ll have to defer to your experience and trust the last statement.
But the rest of the reasons dont make much sense to me.
I will say, side post batteries in general are a bit more finicky for getting good connections to the battery in older/less than perfect conditions. And they are never preferable to top post.
But battery life is so subjective to so many factors, it would be almost impossible to pinpoint longevity on post location imo.
 

nvrenuf

Full Access Member
Joined
Jul 30, 2010
Posts
2,711
Reaction score
4,296
Location
Mobile, Al.
First Name
John
Truck Year
1991
Truck Model
K5
Engine Size
454
I didn’t realize this thread existed so no pics but I replaced the water pump on the Cummins in my ‘06 Dodge today, crazy easy compared to Pumps I’ve done on other engines - remove the air filter box, take the belt off and there’s 2 bolts - done.

Other manufacturer engineers could learn a lot from this design.
 

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
I didn’t realize this thread existed so no pics but I replaced the water pump on the Cummins in my ‘06 Dodge today, crazy easy compared to Pumps I’ve done on other engines - remove the air filter box, take the belt off and there’s 2 bolts - done.

Other manufacturer engineers could learn a lot from this design.

'87-'07-ish GM 2.8/3.1/3.4/3.5 were a very similar design. Remove belt, remove water pump pulley, then there's the 5 bolts holding the water pump insert into the housing. It's stupid simple.

I realize that 5 bolts is more than two, lol. But removing the belt is easier on them then a Cummins with a mechanical fan, so that makes up for it.
 

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
7,611
Reaction score
28,869
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
'87-'07-ish GM 2.8/3.1/3.4/3.5 were a very similar design. Remove belt, remove water pump pulley, then there's the 5 bolts holding the water pump insert into the housing. It's stupid simple.

I realize that 5 bolts is more than two, lol. But removing the belt is easier on them then a Cummins with a mechanical fan, so that makes up for it.
Was gonna say, all the GM LS engines (4.8/5.3/6.0/6.2) are that simple. Remove the belt, pop 2 hoses off, 6 bolts, slam it back together. Pulley comes with the pump.
 

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Was gonna say, all the GM LS engines (4.8/5.3/6.0/6.2) are that simple. Remove the belt, pop 2 hoses off, 6 bolts, slam it back together. Pulley comes with the pump.

Nope, way easier than the LS even. Especially with a mechanical fan.
 

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
That's why we buy '05+ trucks, E-fans make it a breeze

Yeah, but still way easier lol. It's at the front of the engine, up high and easy to get to also. No clamps or hoses to remove at all. No thermostat or housing to deal with. The belt slips right off and tends to stay on the rest of the pullies. In most applications, there's nothing else underhood that's really in the way.

At one point (maybe still?) Holley offered a front accessory kit for the LS that utilized a little water pump insert. I never saw one in person, but that little water pump insert may have just been a GM 60* V6 water pump.

You must be registered for see images attach
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
10,712
Reaction score
20,955
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Went to check the transmission fluid. Like lots of vehicles anymore,you have to pull the speedometer drive and check the fluid through that opening. We'll mine was stuck sure I could have jacked it up got under it got creative with a punch and a hammer,OR!!!! I clamped a loop of wire to the side of the speedometer drive with vice grips. The loop was long enough to snake past everything and stick up 6 or 8 inches above the intake and valve cover. I stuck a hammer in the loop and swung the hammer a couple of times. The hammer swinging into the closed loop create a severe and sudden jolt on the speedo drive and popped it out. This trick works for more than just speedo drives but I had to do this today so thought I'd pass it along. The Pic is an air fitting,smaller vice grips and a junk claw hammer. Just to give you all a visual,I wasn't going to remove the speedometer drive to get a pic and I left the vice grips and ball peen in the cars tool box. So you have to use a little imagination. The hammer wire and vice grips are oriented though in the position I had to pop the speedo drive.
You must be registered for see images attach
 
Last edited:

Sgt Gus

Full Access Member
Joined
Aug 2, 2023
Posts
915
Reaction score
1,816
Location
Texas
First Name
Mark
Truck Year
87
Truck Model
R20 3/4 ton
Engine Size
454ci/7.4L
Finally all safety inspected and registered after this mayhem. My 2011 Tahoe
You must be registered for see images attach
Oof, I was about to give up on a lower ball joint on my 2003 suburban, when my neighbor encouraged me. ✔️ ⏳️
 

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Adjusted the passenger door so it closed easier, as it had been dragging on the striker. The hinges are welded, used my handy dandy bendy bar to get the job done.

Also tightened up the track bar bolts because they were making a knocking noise on bumps.

Unfortunately, I chipped paint off the door during the adjustment procedure and now one track bar rod end is groaning during suspension movement. If it ain't one thing, it's another.

You must be registered for see images attach
You must be registered for see images attach
 

410 John

Full Access Member
Joined
Jan 26, 2023
Posts
732
Reaction score
2,143
Location
HdG, Maryland
First Name
John
Truck Year
1983
Truck Model
C10
Engine Size
350 4bbl 4 speed
Adjusted the passenger door so it closed easier, as it had been dragging on the striker. The hinges are welded, used my handy dandy bendy bar to get the job done.

Also tightened up the track bar bolts because they were making a knocking noise on bumps.

Unfortunately, I chipped paint off the door during the adjustment procedure and now one track bar rod end is groaning during suspension movement. If it ain't one thing, it's another.

You must be registered for see images attach
You must be registered for see images attach
How many Celebrities do you own?
 

bucket

Super Moderator
Staff member
Moderator
Joined
Aug 3, 2010
Posts
36,070
Reaction score
46,941
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
How many Celebrities do you own?

6 of them, I think. One of those I had been using as a parts car. But I've got enough parts to build all 6 of them into complete drivers.
 

Latest posts

Forum statistics

Threads
48,830
Posts
1,090,957
Members
44,119
Latest member
79TanSquare
Top