Search results

  1. DoubleDingo

    Vacuum hose routing

    Replaced the vacuum hoses on the truck. Some were new but I replaced them anyways. My question: On the sticker, does the "nut/bolt" looking part of the EFE TVS and SPARK TVS on the diagram indicate the portion you put a wrench on to tighten them? If so, does it matter how the hoses are...
  2. DoubleDingo

    Prepping Plastic for Paint

    I recently ordered a new cowl for my 1991 Jeep Cherokee, so a Chrysler squarebody...lol... It appears to be plain plastic, it's black. What should I do to prep it for paint? My old one warped in the summer sun, and I was able to find a new one from Mopar. The new one was actually the same...
  3. DoubleDingo

    Have any of you replaced engine mounts on a 2012 f150?

    My neighbor has a 2012 F150 2wd. He needs to replace the engine mounts. He got a quote for 2k! He then asked me if I would. I am certain it's not easy like these old trucks. I am reluctant to take it on, because I don't want to mess it up. If you have done this job before on a 2012 F150...
  4. DoubleDingo

    Preferred Solder for Automotive Wiring

    I normally use butt connectors on wiring, however, I have seen in the manuals, to do a wire splice, to cut the insulation about 1/2 inch off of each wire, mesh the strands together, then solder and heat shrink. Heat shrink obviously goes over the wire first, or one gets to redo the splice. I...
  5. DoubleDingo

    th350 vs th400

    Let me ask this a different way. What is the difference in the dipstick diameter and location between the th350 and th400? Is the th400 further back, different angle? I was thinking maybe different sides, but these photos show them on the same side.
  6. DoubleDingo

    TH350 dipstick tube and dipstick for a TH400???

    I asked yesterday in an old thread, I decided to start a new one today. Will a th350 dipstick tube fit the th400 case? To me, they should be the same. But I am not that familiar with both transmissions to know for a fact.
  7. DoubleDingo

    Runs smooth, then sputters, then smooth, then sputters

    What is on the truck: Vortec heads. National carburetor quadrajet for an electric choke 3/4 ton truck. All the factory tubes and pieces. No EGR, just smog pump and plumbing for that. The new carb had been doing a great job since October 2022, and about 4 tanks of gas had been run through it...
  8. DoubleDingo

    Rope Cleats

    Does anyone have a set of these that they are willing to get rid of? I need 6 of them. The only thing I can find online close to them are horseshoe-shaped ones on etrailer. Thanks.
  9. DoubleDingo

    Hazard Switch won't turn off

    Yesterday I replaced bulbs so everything was fresh. It fixed some of my turn signal issues. I still have to track down some gremlins so the turn signals work like they should. Right before sundown today I went to test the hazards to make sure those work, knowing that the driver's side front...
  10. DoubleDingo

    Eastwood Roll-On Primer

    Have any of you used the Eastwood Opti-Flow Roll On Primer? I am really looking hard at this for when I start doing the body work on Crusty. Seems like a good way to go, and once it is done, it can be painted by a shop. https://www.youtube.com/watch?v=2Jq3CQ8UdcY
  11. DoubleDingo

    73-87 14 bolt hubs

    I recently discovered that 14 bolt brakes can be swapped on to the old HO52/HO72 rear axles, with a little creative engineering. If I read everything correctly from those threads on the 67-72 website, the 14 bolt hub needs to be machined to accept the HO52/HO72 inner bearing. The outer bearing...
  12. DoubleDingo

    Inside Micrometer - Is this harbor freight unit worth a a darn?

    I need to mic the cylinders in my 292 and have been looking for a micrometer to do the job. On Grainger they range from $800 to $4,000+. For something I won't use very often I am not going to pay a huge amount, but I want it to be accurate. Do any of you have experience with these harbor...
  13. DoubleDingo

    What are your thoughts on this Holley Sniper 2GC EFI

    https://www.holley.com/products/fuel_systems/fuel_injection/sniper_efi/sniper_efi_2gc/sniper_efi_2gc_small_bore/parts/550-864K I was looking at options for fuel/air delivery on the 292 and saw this. This just may be the ideal setup for my 1.94/1.60 valved, lump headed 292, with ductile iron...
  14. DoubleDingo

    Double Dingo's 1991 Jeep Cherokee

    I'll have to dig up some older photos to keep this more chronological, so bear with me as I find them. I bought this Jeep in 2002. It was my first vehicle that I had to buy from a non-family member. I saw the ad in the newspaper I took with me on one of my visitation weekend trips. I...
  15. DoubleDingo

    Selecting the correct camshaft

    Nope, I'm not going to ask you guys if a Thumper cam is the right one for my engine because it sounds cool at idle. I saw this video and thought it could be valuable on here. Perhaps a sticky for when the inevitable cam questions arise. We could show them this. Mods, if this is in the...
  16. DoubleDingo

    Steering Column Sector Gear and Rack

    Have any of you had experience replacing the steering column sector gear and rack for the steering wheel lock feature? Is it a pain to tear apart the steering column to get to the parts? Right now my jeep is dead. I can't even jump start it because I can't shift the transmission out of park...
  17. DoubleDingo

    Bleeding a hydraulic clutch system on a 2007 Forester

    I replaced my master and slave cylinders on my Forester over the weekend. I thought bleeding the system was pretty straight forward, like bleeding brakes. Apparently not. No fluid wants to come out of the bleeder valve on the slave cylinder. Have any of you ever bled a clutch system on a...
  18. DoubleDingo

    Question for you out there that have run a 292 in a truck

    Do any of you guys on here have any experience with trucks that had a 292 in them? I am considering a 292 for Crusty Biscuit. I know they have a very flat torque curve and from what I've heard are a pretty decent engine.
  19. DoubleDingo

    Air Cleaner Housing Doohickey

    Yesterday I was driving to get some lunch. Waiting at a light and I feel the truck surge and the idle went up. The choke works flawlessly, carburetor does too, and the truck wasn't stumbling or anything, just the idle wouldn't settle down. After work I was waiting to pull out on the street...
  20. DoubleDingo

    Clutch Question

    I am asking this for my stepdad (Pop). He has a '69 F250 4x4. I know this is a Chevy site, but I also know you guys have probably worked on many different makes and models through the years. With that said, here is his dilemma. He bought a 12" clutch to replace the clutch in the truck. He has...
  21. DoubleDingo

    Modulator Valves

    I haven't done a whole bunch of research on this, but I thought I'd at least bring it up. My truck still shifts weird sometimes, so I figured a new modulator valve may be in order. Sometimes the shifts are noticeable, sometimes they're soft and sounds like it only shifted once. Since I have...
  22. DoubleDingo

    TH400 acting oddly

    A few months ago when I went to the bulk yard, I was backing into the driveway and noticed the truck acting weird. Gave it a little gas, it would go backwards, let off the gas and acted like bearing flat spots and you could hear the driveline chattering as the truck slowly rolled to a stop...
  23. DoubleDingo

    Inquiry about an all original 81 Silerado

    I've been on the fence about selling this truck for a while. I'm the 3rd owner, it has under 80,000 miles on the odometer. I hate seeing it go because it's a last of its breed numbers matching 3/4 camper special. But, I made a comment to my cousin I had a truck to sell. He's wanting a price and...
  24. DoubleDingo

    1965 3/4 Ton Blank Canvas

    1980 El Camino']1980 El Camino[/URL] @Snoots Here you go. In 2005 I was driving to church for the Wednesday Bible Study. It was mom's birthday too, and all was well. I daily drove Mean Green at the time. Mean Green was my grandpa's truck when I was a young teen. He passed in '87 and...
  25. DoubleDingo

    American Racing Outlaw II Wheels

    What do you guys use to clean Outlaw II wheels? I think there is a clear coat on them. Would just plain soap and water work?

Latest posts

Forum statistics

Threads
42,119
Posts
909,525
Members
33,612
Latest member
Knep115
Top