Search results

  1. MrHorsepowerLSx

    High Pressure Gas shooting out filler hole

    @ocsolarguy Can you snap some pics of the "4" charcoal canisters and post them here for us to see.
  2. MrHorsepowerLSx

    Holley Sniper

    Sold, thanks to all who inquired
  3. MrHorsepowerLSx

    Holley Sniper

    LS swap, my new SBC has to go back to machine shop. Has oil control issue. I’m trying to recover some funds spent on this build
  4. MrHorsepowerLSx

    Holley Sniper

    Excellent condition Sniper EFI unit. Has only 4 hrs on it. I’m including a new Accel HEI distributor and 14” black air cleaner, window mount for the 3.5” monitor as well. Air cleaner and distributor not pictured yet. I bought the Holley system around April of 2023 and installed it around August...
  5. MrHorsepowerLSx

    74 k10 going 55 mph is at 3,500 rpm

    Any progress made over the weekend?
  6. MrHorsepowerLSx

    Dual Reservoir Brake Master Cylinder - which outlet for F vs R?

    The prop valve will need to be changed from factory disc/drum to disc/disc as well. Just a reminder.
  7. MrHorsepowerLSx

    Dual Reservoir Brake Master Cylinder - which outlet for F vs R?

    Larger the line the more volume and less pressure. Smaller the line more pressure less volume. Pressure is a restriction to flow. You don’t want the rear brakes having more stopping power then the front.
  8. MrHorsepowerLSx

    K10 Misfiring

    When you mentioned " sounds like a rev limiter" are you saying the transmission is slipping or that the misfire is so bad that it is not firing and the motor is pinging? Are you still on the factory TBI or converted to a carb?
  9. MrHorsepowerLSx

    New TBI injectors causing surging

    Are the "new" injectors for a small block or the big block? Food for thought is if you purchased larger flowing injectors and had a custom chip burned for the SBC OEM flow rates that will cause drivability/idle issues
  10. MrHorsepowerLSx

    2.5 Rockwells is anybody running these

    Welcome back!
  11. MrHorsepowerLSx

    High Pressure Gas shooting out filler hole

    Hellova first post :) Try running the truck with the gas caps off and see if that fixes the issue. If yes proceed to correcting the tank vent issue or replace the fuel cap with caps that are vented
  12. MrHorsepowerLSx

    Fixing vapor lock now that I barely made it home, experience with 3 port filters?

    As side note, if you install a return line don't hook it up to the tank vent, hook it to the smaller 1/4" nipple coming off the tank. You could always check which line you need by pulling the sending unit and inspecting or by blowing air with your mouth into the tank with a piece of hose. The...
  13. MrHorsepowerLSx

    Under dash air box hvac.

    Happen to have a pictures of the problem area.
  14. MrHorsepowerLSx

    Question on RTV if needed or not

    Nope, most of those gaskets are 1/16th of an inch. That's not enough to cause an engagement with the splines. Sealant just complicates removal sometimes and if to much is used it will get into the fluid and can be passed around between the trans/transfer case.
  15. MrHorsepowerLSx

    2.5 Rockwells is anybody running these

    I'm am grateful that Vince left behind all that valuable info. We should make this a sticky in his honor. :) Plus I really enjoyed reading it.
  16. MrHorsepowerLSx

    Question on RTV if needed or not

    Pick one or the other avoid using both, if you "glue" the paper gasket it really makes it a pain when you have to service/remove it. I personally like the gaskets and have never had an issue. I've also used Ultra Grey when a gasket was not available, a little bit goes a long way and sometimes it...
  17. MrHorsepowerLSx

    Stock DBC 3 bolt Throttle body

    I forgot I posted that, I found one thank you.
  18. MrHorsepowerLSx

    Is this the original bed on my 85 Chevy k10

    This right here! I'm a sucker for OEM sheet metal on all my builds. I search very hard to find "good" useable pieces for patches or replacements. I try to never by offshore stuff, I did buy 2 bedsides for my project and I've contemplated reinstalling my crappy OEM bedsides due to the terrible...
  19. MrHorsepowerLSx

    Stock DBC 3 bolt Throttle body

    Looking for stock LS throttle body, intake bracket for throttle cable and a throttle cable. The throttle body doesn’t need sensors. Thanks guys
  20. MrHorsepowerLSx

    About to ruin one of the nicest C3500's with an Ls.. Pictures

    Well I’ll be :) I Might just have to take an extended drive in the truck one night
  21. MrHorsepowerLSx

    About to ruin one of the nicest C3500's with an Ls.. Pictures

    I’m about an hour from you. I frequently visit the Eastwood store in Pottstown and we shop at KOP all the time. Better then the Deptford mall I’m in South Jersey as well Sicklerville area. You?
  22. MrHorsepowerLSx

    SBC Cylinder Head Decision

    I have the AFR Enforcers on my K10 SBC build. The truck is doing the same things as your truck, and it runs quite well. I built the motor to run on plain regular octane with low compression and it has no problem making some 11’s on the road with its 35s and 4:56’s the truck also has a 700r4. The...
  23. MrHorsepowerLSx

    Old as dirt,but still above it

    Welcome from New Jersey
  24. MrHorsepowerLSx

    Does anybody know what this is for??

    The passenger side clamp on my 86 K10 held my speedo cable and the drivers side clamp held the wiring for my 700r4
  25. MrHorsepowerLSx

    What transmission do I have?

    Glad you figured it out, @NickTransmissions provided some really great information that you could always reference back to if something else were to happen to your trans down the road not transfer case related

Forum statistics

Threads
42,013
Posts
907,439
Members
33,510
Latest member
dstack12
Top