Search results

  1. G

    really need the experts on this, runs beautiful won't move

    Ok guy's started it with the transfer case in 2 high pushed the clutch in to see if it would get the transmission in gear. no go:mad: the pedal doesn't even have any pressure till about two inches from the floor. I'm guessing it's the throw out bearing. Since I have no place to work on it. I...
  2. G

    really need the experts on this, runs beautiful won't move

    good to know I'll do as suggested and give it another try
  3. G

    really need the experts on this, runs beautiful won't move

    The transfer case isn’t the issue the transmission won’t engage a gear. When I push the clutch in if I try to select any gear it just grinds won’t even come close to going in gear
  4. G

    really need the experts on this, runs beautiful won't move

    talked to an old school guy with a shop around the corner from me, says he's seen it before believes I have the wrong throw out bearing installed. He could be right I just ordered it only looked at one, he says there are three different type bearings, said I should remove the cover plate and...
  5. G

    really need the experts on this, runs beautiful won't move

    Grit Dog, no the clutch doesn't feel right to me, does go through the gears smoothly. All new components from Summit 3 prong pressure plate, new disk, installed with an aligning tool went together smoothly. I had the engine pulled so it wasn't that difficult mating it up. When I dropped the...
  6. G

    really need the experts on this, runs beautiful won't move

    yes transfer case in neutral first thing I checked.
  7. G

    really need the experts on this, runs beautiful won't move

    New issue although the biggest I've faced not sure I can fix it. So with the help of the forum guys I got the truck running and sounds fantastic. Went to put it in gear it's a 4sp with a 205 transfer case and no go, when I push the clutch in I get no response can't move it into any gear just...
  8. G

    What’s the best way to fix this?

    So was cleaning up my fuse panel and two things went wrong. Look at this pic and tell me what you guys think. I pulled out the flasher for the hazards and lost one pin completely the other is sticking out. Also one side of one of the fuse holders broke off.
  9. G

    Where is this under dash?

    Thanks guys that’s what I suspected.
  10. G

    Where is this under dash?

    I’m trying to sort out some wiring issues and have the factor book for my 73 I’m not at my truck currently but wondered where is this located under dash and what’s it’s purpose? Seems like it dead ends multiple connections.
  11. G

    Clutch pedal doesn't return all the way?

    In my rebuild I replaced the pressure plate throw out bearing clutch disk etc, new springs and all the linkage is fine. Works properly, however when I push the clutch pedal in it seems to engage and depress at the right level, but when it comes back up from the floor it doesn't return fully. I...
  12. G

    this is a weird one.... lighting question.

    I have power to all the lights they all come on, only the left taillight blinks
  13. G

    Help me out please starting issue?

    Was firing order got it sorted out thanks
  14. G

    this is a weird one.... lighting question.

    Guys, on my 73 k 20 I've got the dash removed no gauges etc. I do have my fuse block and all my wiring intact. So issue is when I pull my headlight switch out I get headlights all the running lights, brake lights and one turn signal left side rear, no other turn signals. How would I trace this...
  15. G

    Carb issues?

    no cold or chilly weather 75-90 pretty much year round, plus I have 3 vehicles so this wouldn't be driven in cold or rain. Thanks for the reply
  16. G

    Got it running

    But when I start it the throttle blade go straight up like there no in between and I’m idling at like 3500 rpm
  17. G

    Got it running

    I’m not sure my high idle cam is working or hooked up properly
  18. G

    Got it running

    When you say wire it open how do I do that I think my issue is I’m on the high idle cam
  19. G

    Carb issues?

    A lot of replies from a post I ran on my truck not starting and shooting flames out the carb. Well that was a timing issue got it worked out, but when I start it the carb races to throttle body wide open. Mind you it doesn’t have a choke that is working. Can I remove all the choke mechanism and...
  20. G

    Got it running

    Guys got it running but the carb is still doing runaway acceleration. I hate this q jet. It’s a divorce choke style and the lower part that attaches to the block is gone. Can I just remove all the choke stuff as I really don’t need one
  21. G

    Fire out my carb?

    to everyone who has suggestions I wanted to clear up one thing the truck doesn't run it will fire over but with fire shooting out the carb I figured it prudent not to continue running it.
  22. G

    Fire out my carb?

    so went out and pulled # 1 plug put a *** of cotton in the hole cranked it with my remote starter till the cotton shot out so #1 should be at tdc looked at the timing mark right on 0 pulled the cap rotor pointing at what looks to be #7 but could also be#1 here are pics
  23. G

    Fire out my carb?

    I’m gonna agree and go back to the basics get the engine one # 1 tdc pull the new hei cap see where it’s pointing and go from there. Thanks
  24. G

    Fire out my carb?

    well it’s been a journey, a lot of you have followed my threads and I’ve finally gotten the headers and the exhaust hung, still haven’t started it since my last attempt when it went wide open on me. So tried it and doesn’t go full throttle but when I attempt to give it gas about every other...
  25. G

    Got it running

    You right I think it does brake booster plug that one also or hook it up?

Forum statistics

Threads
36,195
Posts
764,795
Members
25,351
Latest member
k5350
Top