Search results

  1. T

    What gearing do I need up front?

    Hey everybody! I’ve got a 4:10 geared rear axle that I’m possibly going to be putting on a 4x4 build and was wondering what the best gears for the front axle would be? I will have around 37s for the tires. Thanks for all the help!
  2. T

    Squarebody meetup in Central WA this summer? Interest?

    Ahh, my neighbor goes to that. I’ve got to try and see it sometime.
  3. T

    What have you done to your square lately??

    Look at those wheels on the k5! :roflbow: That suburban looks mean though. I like it
  4. T

    Squarebody meetup in Central WA this summer? Interest?

    Is that the same a Cruise Enumclaw?
  5. T

    2006 5.3 LS4… is it any good?

    Been reading up on it and it’s doable to make it rear wheel drive just not cost affective. Looks like that’s going to be more money than I want to or even have to put into this motor. The search continues …. Thanks for the help
  6. T

    2006 5.3 LS4… is it any good?

    That will all be coming off anyways
  7. T

    2006 5.3 LS4… is it any good?

    I’m looking into a 2006 5.3 LS4 to build for a future project car. Is the LS4 worth building? I’ve heard of and seen a lot of people build the older LS models and they seem to be good engines but wanted to get some feedback from people with LS experience. The owner states that it “…runs well...
  8. T

    Squarebody meetup in Central WA this summer? Interest?

    Where is this being held?
  9. T

    What have you done to your square lately??

    That’s a nice truck! I really like the look with the cow pusher up front
  10. T

    Hello from Arlee,Montana

    Welcome from Washington! I would love to see a picture or five of your truck!
  11. T

    New to GMSB from Oregon

    Welcome from Washington!
  12. T

    Quadrajet rebuild problems

    I think this should help. Had the same problem when I rebuilt my carb. Screw the mixture screws in until they lightly contact the seat. Back out 2 1/2 turns. Back off the throttle/rpm screw all the way. Screw in 2 1/2 turns once it hits the linkage. Hope this helps
  13. T

    Hello from Munich, Germany 87' R10

    Welcome from Washington state! Your truck looks amazing!
  14. T

    Oil pan off, anything I should do while I’m under there?

    Yeah most likely a two piece. I believe the one piece started in ‘86. It’s very simple to do and shouldn’t take much time.
  15. T

    Newby

    Welcome from Washington!
  16. T

    What have you done to your square lately??

    So I’m going to guess you’ve tried it? How well does it work?
  17. T

    What have you done to your square lately??

    Never heard of this being done like that. I’ll have to give it a try
  18. T

    Oil pan off, anything I should do while I’m under there?

    Is it a one or two piece rear main seal?
  19. T

    Oil pan off, anything I should do while I’m under there?

    Yes, at least on my model. It’s a 3/4 ton 2wd with a 350 engine. I’m not sure about other models or engines
  20. T

    Introductions! New member from Florida

    Welcome from Washington! Your rig looks great!
  21. T

    What have you done to your square lately??

    Cleaned the oil pan. Putting on a new gasket because the old one had a million different leaks and made the whole thing nasty… it’s not perfectly clean but neither is the rest of my truck
  22. T

    Oil pan off, anything I should do while I’m under there?

    Probably going be putting a 454 engine in this truck at some point… forget just the crank. ;)
  23. T

    Oil pan off, anything I should do while I’m under there?

    I’m doing the rear main but don’t know how far I want to go with the timing chain and all. I’m planning on building this engine in the spring/summer so I think I will leave that alone for now.
  24. T

    Oil pan off, anything I should do while I’m under there?

    This engine has great oil pressure. I run 60-80 psi all day
  25. T

    Oil pan off, anything I should do while I’m under there?

    Can they be rebuilt/refurbished? It might not even be worth the money if they can

Latest posts

Forum statistics

Threads
48,419
Posts
1,067,010
Members
42,808
Latest member
bajadiver
Top