Search results
-
-
-
-
Oldsmobile Motor Mount Location
I know the F and A body cradles had different holes for different engine placement. The last motor this thing has was the Chevy 267 which is understand is about the same level as the Olds 260. I know the diesels had different mounts so we need someone who has access to one to see if the mounts...- Magna86
- Post #5
- Forum: Engine & Performance
-
Oldsmobile Motor Mount Location
Good Morning Everyone. Are there different locations on the engine cradle for the motor mounts? I'm swapping an Olds motor into my 74. I'm using the trans am mounts on the block so I can use the clamshell frame mounts. Does the Olds motor sit in the same place the 350 was? Sorry if I missed this...- Magna86
- Thread
- Replies: 5
- Forum: Engine & Performance
-
Factory Sway Bar Options
Went back and grabbed one. Added to the future install pile!- Magna86
- Post #35
- Forum: Suspension, Steering & Brakes
-
“What’s up with that old truck” Need help with identification!
Buy it now. Worth it all day!- Magna86
- Post #11
- Forum: Introduction
-
Factory Sway Bar Options
Well looks like I'll have to go back and grab a 4 door one then.- Magna86
- Post #32
- Forum: Suspension, Steering & Brakes
-
Factory Sway Bar Options
No I didn't. The 4 door bar would probably work as the 2 door but need to find different endlink as the ends are straight to bolt thru unlike the 2 door which are flat.- Magna86
- Post #27
- Forum: Suspension, Steering & Brakes
-
Factory Sway Bar Options
Well I struck out at pick in pull. All 4 door blazers. Now to check other yards- Magna86
- Post #19
- Forum: Suspension, Steering & Brakes
-
Factory Sway Bar Options
Well the pick n pull has a few S10 Blazers so time to go looking tomorrow!- Magna86
- Post #16
- Forum: Suspension, Steering & Brakes
-
What have you done to your square lately??
Went junkyard hunting and found a front sway bar with brackets. Cleaned up my parking and turn signal lenses for install. Remove the front turn signal housings to clean up and repaint for install. -
Factory Sway Bar Options
Got lucky and found a front sway. No luck on a rear on the suburbans.- Magna86
- Post #6
- Forum: Suspension, Steering & Brakes
-
-
-
-
Turn Signal Housing Color
What color are the front turn signal housings supposed to be? Mine were white paint bombed and kinda rough so going to clean them up and repaint.- Magna86
- Thread
- Replies: 5
- Forum: Electrical & Audio
-
Factory Sway Bar Options
The local yards dont have square bodies except one and they are very picked over. That's why I'm asking for other vehicles that may have some that work.- Magna86
- Post #5
- Forum: Suspension, Steering & Brakes
-
Factory Sway Bar Options
My 74 doesn't have sway bars but I want to add them. Will the sway bars from a G van bolt onto my C10? Any other factory sway bars that I can swap on for cheap from a junkyard car?- Magna86
- Thread
- Replies: 37
- Forum: Suspension, Steering & Brakes
-
-
What's Missing
Yes I have a cargo lamp. Now to see if there is a connector somewhere. Thanks Guys -
What's Missing
This is the drivers side seat belt anchor point. What goes on this trim panel? I know passenger side has the hanger hook. -
Custom exhaust size?
2.5" nothing more and a good set of mufflers with pipes to exit the rear. Helps eliminate drone and getting black exhaust soot on the truck.- Magna86
- Post #4
- Forum: Engine & Performance
-
Driveshaft vibration
Check your engine and transmission mounts. Do you feel it in the wheel, thru the cab, or a certain area?- Magna86
- Post #4
- Forum: Differential & Driveline
-
What have you done to your square lately??
I went and looked at it sitting in storage. Went junkyard hunting and was successful in locating passenger side filler neck complete with mounting brackets with straps! Too bad the tank was a 20 gal or I would have taken it.
