Search results

  1. V

    Automatic door lock kit

    I’ve got the module from a 98 that I plan to wire into my 84.
  2. V

    1966 Brand New Pick Ups on Rail Car near Mt Shasta

    Here is the original caption for the photo. Also the 65 pickup sales brochure has “panoramic view” trucks on the cover and throughout the brochure. “1964 Northbound Fully Loaded Autoracks. Train #378 hauled vehicles from the GM plant in Warm Springs, CA to the Pacific Northwest. This curve...
  3. V

    4l80e with no controller

    Can make a cheap controller from an 0411 PCM, just need crank signal, TPS and temp.
  4. V

    Scores from DIY Parts Yards, Pull A Part, U Pull It etc

    Been seeing this one in NE GA for years, when we go on vacation to the area.
  5. V

    Scores from DIY Parts Yards, Pull A Part, U Pull It etc

    Picked up a diesel 4wd 4L80 to go in my 6.2 diesel 84. Got about $200 in it including diesel to and from picking it up. Got to pull it so got all the fasteners and small parts.
  6. V

    Which steering bracket from hogback or steering bracket from ORD?

    Hogback doesn’t have any in stock at the moment. I plan to give them a try, but if not back in stock by the middle of Oct, I’ll buy an ORD one.
  7. V

    Picture Please: No Spare Tire Holder

    Sorry, was talking about the spare tire winch
  8. V

    Picture Please: No Spare Tire Holder

    Im fitting the winch setup for an 04 Ram on my 84. Just got bumper, so now sorting bumper, hitch, spare and 4” exhaust. Hopefully get all that fitted next week
  9. V

    Small Block Lifter Premature Wear

    I’ve never seen a lifter wear down like that. Have seen several that the center wore down, but the sides would flair and you’d have to knock it out the bottom. I’d definitely call Lunati. May or may not help. In the early 90s, we (close to a dozen of us) were wiping lobes left and right on...
  10. V

    Removing dent without backside access

    May not work in your case, due to access (may could come in thru the interior light hole) but would tools like this work? The Blue and black handled rods in lower part.
  11. V

    1973 Monte Carlo Very Rare Factory Sunroof - $6,500

    From the 73 MC sales brochure
  12. V

    Fuel gauge reading past full

    I didn’t read all the posts, but when my gauge read at 3 o’clock, i pulled the sending unit and cleaned the connection from the float rheostat to inside pin connection at the top of the sending unit. Got my gauge back working right.
  13. V

    TBI I need help

    See if these help, from the 88 service manual I had an issue recently, that we thought was a fuel issue when it ended up being the MAP sensor. Can post a quick to check it with just a multimeter
  14. V

    Bucket seat swap

    Bucket seats have 2 extra brackets for the inside front brackets of each seat
  15. V

    tbi wiring harness

    Here is a complete tbi harness from a square body Blazer with a 5.7/700r4. It is basically stand alone. Bolts to fusebox bulkhead connector as other engine harness does, and round grommet just down from ecm is where wiring goes back in firewall placing ECM above glove box. The rest is just...
  16. V

    tbi wiring harness

    I’ve got a harness from an 88 k5 Blazer 5.7/700r4) and it is stand alone. Will try to remember to get it out and get pictures. May have one from an obs too, but I believe there is another bulkhead connector on the obs harness.
  17. V

    305 to 454 Engine Swap?

    No, there is no chip like the older tbi ecms. And yes, the 0411 is a better, more tunable ecm than the old black box ones.
  18. V

    Let’s see your memorabilia?!

    Original 1840 dated land patent to my 4th great Wilkinson grandfather.
  19. V

    305 to 454 Engine Swap?

    The cams in the Vortec 7.4s are a “lazy” design, but to swap it, you really need to go to adjustable rockers. They are good engines, good flowing heads, and the intake system makes good torque. Plus it has individual injectors, unlike the Vortec small blocks/4.3, if you want to keep the fuel...
  20. V

    O'Reilly sux balls !!!

    We’ve got a Carquest and a Napa. I use the Napa a lot more since Carquest was taken over by Advance Auto Parts. I know the owners of both very well. Now the CQ has to push Fram filters, so they lost a lot of business. The Napa store doesn’t have as much inventory, but will do his best to get...
  21. V

    Old Gas Can

    Was cleaning out the barn the other day and found 3 - 5 gal military Jerry cans that I had forgotten about. Was using them a few years ago for diesel for my tractor. Will clean them up and put in our youth’s fundraiser sale next month
  22. V

    Steering box brace kits

    I plan to get a Hogback Fab one if they ever come back in stock. https://hogbackfab.com/products/73-87-gm-steering-box-reinforcement-bracket
  23. V

    14 bolt newbie question.

    The 1 ton srw axles have different spring perch width (40.5” vs 42”)and the shocks are reversed and located differently as 1 tons have the shocks inside the frame The 3/4 ton axle shares the 42” perch spacing and shock locations with the 1/2ton
  24. V

    power window relay

    Its pretty simple. 2 relays per door. You will cut and add the relays in the wiring from the switch to the motor. Hardest part is pulling the hot wire. Wire it as per this diagram.
  25. V

    Best seat options ?

    I have a 2014 Ram bench bucket in mine that has the cup holders in the fold down console

Latest posts

Forum statistics

Threads
48,419
Posts
1,067,015
Members
42,808
Latest member
bajadiver
Top