Search results
-
P
Floor Mats
They look original to me.My 87 look very similar, albeit my driver side "heel" area is nearly worn through -
P
1st gen Cummins A/C
Hunter, there is most likely a restriction, probably the condenser, and by that I mean internally not airflow across the coils- Poppy 87
- Post #4
- Forum: Other Vehicles
-
P
My Rear End Build For My Low Buck Street/Race Truck
No idea, but my thought would be clamping the springs such as they are would almost duplicate shortening it thus changing spring rate? Poor man's ladder bar?- Poppy 87
- Post #45
- Forum: Engine & Performance
-
P
K Series Kohler, 2 cylinder - Oil Consumption - Advice?
Being that the engine runs, I would perform a compression test. Follow up with leak down test. Read up on that. Its an internal combustion engine so no special diagnosis required. Good luck- Poppy 87
- Post #2
- Forum: Other Vehicles
-
P
No spark problems.
As you stated HEI would eliminate points and capacitor. I lean towards coil as well. The ignition control module typically are not intermittent, either they work or do not.- Poppy 87
- Post #11
- Forum: Engine & Performance
-
P
What have you done to your square lately??
For what it's worth, the late model trucks use dual fans. With a combination of 3 relays, can actually switch the fan speeds depending on demand. Sent from my XT1254 using Tapatalk -
P
What’s #15 mean?
Get those harbor freight jack stands replaced!! Some are under recall -
P
Refurbishing Dash
If proceeding this way, I would ask an upholstery shop for a quote to do that. I'm gonna do this when I'm ready to do mine, but have no idea of cost -
P
Fitting a 76’ Grille in my 79’?
You have a nice looking old beater!! -
P
Any such thing as a good Service Manual?
For years the publisher of the service manuals, unit repair, wiring, and owner manuals was Helms. Try a search, been a while but that's what I did prior to the internet. By the way, nothing better than factory manuals. Haynes, chilton, motor, are meh- Poppy 87
- Post #33
- Forum: Engine & Performance
-
P
Different tires or LSD in front or back?
Taylor, have you considered mounting the plow to your tractor? With some fab and welding you may be able to do this with parts on site- Poppy 87
- Post #50
- Forum: Tech Discussion
-
P
Mystery tool
Appears to be some type of hole punch? Not sure just a guess, perhaps for leather or upholestery- Poppy 87
- Post #7
- Forum: Tech Discussion
-
P
Headlights go on and off
Doug, sounds like a ground issue. Big block and small block can use the same distributor. Good luck- Poppy 87
- Post #23
- Forum: Electrical & Audio
-
P
Carb or Fuel delivery problem?
Next check I would do is fuel filter- Poppy 87
- Post #2
- Forum: Carb Fuel Systems
-
P
What have you done to your square lately??
I was just messing with you! That coal slag appears to work well. Is that a common blast media? Sent from my XT1254 using Tapatalk -
P
What have you done to your square lately??
Glad to see you got the rona mask on too! Sent from my XT1254 using Tapatalk -
P
What have you done to your square lately??
All the talk of being color blind, weren't you guys tested? I'm 55 and we had testing for that in elementary school, guess that was early 1970's. I grew up in Minnesota Sent from my XT1254 using Tapatalk -
P
77 K10 LS Swap
Brother, the pictures you post earlier sure look more like filter debris than fuzz from a rag unless you aren't meticulous with cleaning. Wouldn't expect Fram to admit fault anyway Sent from my XT1254 using Tapatalk- Poppy 87
- Post #431
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
P
Manual Hub Identification
The 50 pound feet sets the preload. Back off ONLY enough to install the locking mechanism. Heck if you want to, place the fish scale on the lug nut and verify! We put many of these kits on back in the day- Poppy 87
- Post #21
- Forum: Front Diff & Hubs
-
P
77 K10 LS Swap
That's awesome! How much $$ invested? Sent from my XT1254 using Tapatalk- Poppy 87
- Post #425
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
P
Manual Hub Identification
Back in the 80's we used to put the manual lock hubs on these trucks. I would just do a search using your vehicle. Seems like Warn used to make them. Complete kits were not too $$$$.- Poppy 87
- Post #5
- Forum: Front Diff & Hubs
-
P
700R4 Rebuild cost
I build my own transmissions whether it be automatic or manual. The last 700R4 I did for my son in law's '90 silverado was a stock type build with reman torque converter. Parts cost about $350 because it had some hard part damage. (he had a tendency to throw it into park when backing down the...- Poppy 87
- Post #27
- Forum: Transmission & Transfer Case
-
P
Do we have a show us your shop thread?
That shop is nice, how high is your ceiling and door opening? I'm still in planning stage, but am definitely installing a 2 post lift -
P
Do we have a show us your shop thread?
Same here, I just moved across state and I'm gonna build a shop
