Paint Stripper

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

custodian

Full Access Member
Joined
Apr 15, 2016
Posts
959
Reaction score
554
Location
Catawba
First Name
William
Truck Year
1973, 1985
Truck Model
C10
Engine Size
5.3 LS, 350
What would be a good paint stripper to remove single layers of paint off at a time? My 73 has been painted several times and would like to slowly get down to the original paint.
 

waterpirate

Full Access Member
Joined
Jan 2, 2019
Posts
823
Reaction score
1,840
Location
delaware
First Name
Eric
Truck Year
1987
Truck Model
v10
Engine Size
5.7 tbi
I have used the non toxic citrus strip and it seemed to take off the paint 1 layer at a time. Pain in my a$$, but it might be just what you are after.
Eric
 

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
1,589
Reaction score
2,150
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
As soon as any stripper is used surface needs to go to metal. I used aircraft stripper, neutralized with water. Like everything automotive and especially refinish products take a big *** of cash.
Just purchased 1 gallon of surfacer $429 + $202 for catalyst.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
3,939
Reaction score
5,691
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Wet it with gasoline see if that's enough,a lot of time soaking enamel in gas is enough to cause it to lift,but won't hurt a factory finish. Next on the list lacquer thinner same deal it will lift most finishes but not the factory paint its just a hotter solvent than gas. Lastly physically sand it start using finer grits as you start seeing factory paint. I have also taken off spray paint vandalism with the buffing pad and rubbing compound.
 
Last edited:

custodian

Full Access Member
Joined
Apr 15, 2016
Posts
959
Reaction score
554
Location
Catawba
First Name
William
Truck Year
1973, 1985
Truck Model
C10
Engine Size
5.3 LS, 350
I have used the non toxic citrus strip and it seemed to take off the paint 1 layer at a time. Pain in my a$$, but it might be just what you are after.
Eric
How long did it take to work. Working on one area at a time, fender, front part of bed side, etc....
 

waterpirate

Full Access Member
Joined
Jan 2, 2019
Posts
823
Reaction score
1,840
Location
delaware
First Name
Eric
Truck Year
1987
Truck Model
v10
Engine Size
5.7 tbi
Took like 30 minutes to soften the paint, then removed the paint with coarse green scrub pads, rinsing in water.
Eric
 

custodian

Full Access Member
Joined
Apr 15, 2016
Posts
959
Reaction score
554
Location
Catawba
First Name
William
Truck Year
1973, 1985
Truck Model
C10
Engine Size
5.3 LS, 350
Took like 30 minutes to soften the paint, then removed the paint with coarse green scrub pads, rinsing in water.
Eric
Doesn't sound that bad. Not in a hurry.
 

waterpirate

Full Access Member
Joined
Jan 2, 2019
Posts
823
Reaction score
1,840
Location
delaware
First Name
Eric
Truck Year
1987
Truck Model
v10
Engine Size
5.7 tbi
Let us know how it goes!
Eric
 

Camar068

Supporting Member
Supporting Member
Joined
Feb 5, 2014
Posts
4,122
Reaction score
2,960
Location
Kentucky
First Name
David
Truck Year
1986
Truck Model
K10/LM7 5.3/4L60e/np208/3.73/32"
Engine Size
10 yrs Air Force
I have used the non toxic citrus strip and it seemed to take off the paint 1 layer at a time. Pain in my a$$, but it might be just what you are after.
Eric
you can put the citristrip, in a small section, the put saran wrap over it and let it sit for 24 hours. See how much comes off. The saran wrap keeps the citristrip gel moist and doesn't let it dry. Makes it "a little goes a long way".
 

CalSgt

Full Access Member
Joined
Oct 3, 2021
Posts
1,471
Reaction score
3,056
Location
CA
First Name
Casey
Truck Year
1980
Truck Model
Chevy K-10 Custom Deluxe
Engine Size
350
What would be a good paint stripper to remove single layers of paint off at a time? My 73 has been painted several times and would like to slowly get down to the original paint.
Honestly man, I don't think theres any way to strip a layer at a time & not have it turn out looking like a chewed on half dissolved jaw breaker.

Why the desire to strip a layer at a time if I may ask?
 

custodian

Full Access Member
Joined
Apr 15, 2016
Posts
959
Reaction score
554
Location
Catawba
First Name
William
Truck Year
1973, 1985
Truck Model
C10
Engine Size
5.3 LS, 350
Honestly man, I don't think theres any way to strip a layer at a time & not have it turn out looking like a chewed on half dissolved jaw breaker.

Why the desire to strip a layer at a time if I may ask?
Not taking it all the way to metal at this time.
 

CalSgt

Full Access Member
Joined
Oct 3, 2021
Posts
1,471
Reaction score
3,056
Location
CA
First Name
Casey
Truck Year
1980
Truck Model
Chevy K-10 Custom Deluxe
Engine Size
350
Not taking it all the way to metal at this time.

Get yourself a DA and some 120 grit paper and feather the whole thing out.

ETA: Unless the paint has major flaws like crowes feet, cracks, peeling or curdling or theres old body work failing, I don't recommend taking it down to bare steel. Feathering out the existing paint fills low spots and gets thin on high spots, it's like free primer.
 
Last edited:

custodian

Full Access Member
Joined
Apr 15, 2016
Posts
959
Reaction score
554
Location
Catawba
First Name
William
Truck Year
1973, 1985
Truck Model
C10
Engine Size
5.3 LS, 350
Get yourself a DA and some 120 grit paper and feather the whole thing out.

ETA: Unless the paint has major flaws like crowes feet, cracks, peeling or curdling or theres old body work failing, I don't recommend taking it down to bare steel. Feathering out the existing paint fills low spots and gets thin on high spots, it's like free primer.
Reworking some long ago body work that has cracked and bubbled. I have an orbital sander with the Velcro attachment.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
3,939
Reaction score
5,691
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Lacquer thinner will take off,most refinishes,and leave the factory finish on the car. Thats why we were able to shoot Lacquer on a repaint over factory finish,but if you shot it over an enamel repaint it would lift. I'm sure some of you have shot incompatible paints and watched ever thing desolve and crinkle up.
 

Latest posts

Forum statistics

Threads
41,853
Posts
903,548
Members
33,366
Latest member
texdave
Top