Cutting coils

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Wannabe

Member
Joined
Nov 27, 2022
Posts
40
Reaction score
31
Location
Streator, IL.
First Name
Chuck
Truck Year
1973
Truck Model
C10
Engine Size
350
I have been reading threads about lowering and I see that everybody says to only cut one coil. I's like to know why only one? Will there be problems with cutting 2? I know it will make the ride stiffer but is there any other reasons?
 

Snoots

Full Access Member
Joined
Jan 23, 2013
Posts
8,158
Reaction score
15,957
Location
Georgia
First Name
Roger
Truck Year
1973
Truck Model
Jimmy Sierra
Engine Size
350
Seriously, cutting 2 coils will lower it more but at that point you start messing with the entire suspension. If it's a 4x4, you've also shortened or altered the driveshaft angle. Since you show you have a C10 this shouldn't be a problem. You have to cut the spring directly below where the coil ends so that it remains symmetrical.
With 49 year old springs I'd just buy shorter NEW ones.

Good luck with your project!
 

GXPWeasel

Full Access Member
Joined
Nov 5, 2019
Posts
573
Reaction score
1,033
Location
Kansas
First Name
Greg
Truck Year
1982 | 2015
Truck Model
Sierra C15 | Silverado Z71
Engine Size
5.0 | 5.3
Keep in mind, if you do cut even 1 coil out of your springs, you will more than likely need lowered shocks as well. Ask me how I know. I have a great front set of brand new KYB's that I couldn't install.
 

Keith Seymore

Full Access Member
Joined
Jul 13, 2015
Posts
2,609
Reaction score
8,018
Location
Motor City
First Name
Keith Seymore
Truck Year
1987
Truck Model
R10
Engine Size
4.3L
Basically the ratio is 1:2, due to the placement of the coil spring in the control arm.

That is, one INCH off the coil will result in a drop of two inches at the fender opening.

K
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
3,945
Reaction score
5,697
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
The more you cut it the more you change the spring rate also the more you cut it the more you affect front end geometry. If you need to go lower,buy spindles.
 

Wannabe

Member
Joined
Nov 27, 2022
Posts
40
Reaction score
31
Location
Streator, IL.
First Name
Chuck
Truck Year
1973
Truck Model
C10
Engine Size
350
Thanks to all who replied, I know one coil will not get it down where I would like to have it and I am very aware of what cutting the spring will do to the control arm angles. So I guess I'll just have to bite the bullet and get spindles. I would ask Santa for them but he isn't talking to me.
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
3,945
Reaction score
5,697
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Santa exactly what do you mean by naughty?
 

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
2,552
Reaction score
8,271
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
The other thing to remember when cutting the coils is where the pig tail sits in it's pocket. If you don't get that in the right spot, the coil can move around and make noise. I kept cutting mine 1/4 coil at a time till I was happy with where the truck sat and the pigtail was in the right spot. I probably cut 1.5-2 coils off (can't remember exactly and each side is different to account for the Chevy lean).
 

Catbox

Full Access Member
Joined
Jul 12, 2018
Posts
3,968
Reaction score
14,481
Location
Just Outside of Portland Oregon
First Name
Peter
Truck Year
1979
Truck Model
C20 Silverado Camper Special
Engine Size
461
For an example...
This is my 1954 Bel Air after I had the hydraulics removed.
It was put on stock height suspension that I picked up.
Sits way to high over the 205/60/15's it wears.
You must be registered for see images attach


So to remedy the situation in the front, we ended up removing 1-1/4 coils in the front.
That has been the only change made here, other than the location of the vehicle.
You must be registered for see images attach

No more fender gap above and it settled down right over the top of the tire.
Small changes make bigger than you might think differences.

I then added a set of 3 inch lowering blocks to the rear and got the whole car to settle back down close to where it used to be.
You must be registered for see images attach
 

DoubleDingo

Full Access Member
Joined
Jul 3, 2012
Posts
10,019
Reaction score
14,164
Location
Right where I am
First Name
Bagoomba
Truck Year
1981, 1965
Truck Model
81-C20 Silverado Camper Special-TH400-4.10s; 65-C20 with 4:57 gears and Borg Warner Overdrive
Engine Size
Carb'ed Vortec 350; 1972 L48 350
@Catbox I like it, but like it more before the rear got lowered. It's not my car, and I like some rake to my vehicles, not stinkbug rake, stock stance rake looks cool.
 

Catbox

Full Access Member
Joined
Jul 12, 2018
Posts
3,968
Reaction score
14,481
Location
Just Outside of Portland Oregon
First Name
Peter
Truck Year
1979
Truck Model
C20 Silverado Camper Special
Engine Size
461
It still retains a modest amount of rake.
When it becomes an actual project again, I will be putting a whole new suspension under it.
Then it will be set up proper hot rod like.
Here it looks level, but it is sitting on a slanted part of the yard.
You must be registered for see images attach


This was before when it was on hydro's.
The PO installed them as ghetto cheap as he could and I did not know the system well enough to see how poorly he did it.
Lucky for me he was interested in trading back for them.
So I sourced the parts and he did the remove / reinstall for the junk hydro set up.
Don't get me wrong, they were fun to have.
But they needed to be done the right way for any long term driving.
You must be registered for see images attach

You must be registered for see images attach

It laid out nice at the bottom of the hydros...
 

bluex

Full Access Member
Joined
May 9, 2013
Posts
1,833
Reaction score
2,121
Location
Spartanburg SC
First Name
Paul
Truck Year
1978
Truck Model
C15
Engine Size
350
I have been reading threads about lowering and I see that everybody says to only cut one coil. I's like to know why only one? Will there be problems with cutting 2? I know it will make the ride stiffer but is there any other reasons?
2 makes the spring too short an it will fall out of the pocket when you jack up the truck. It can still be aligned but the guy won't like you very much lol.
Keep in mind, if you do cut even 1 coil out of your springs, you will more than likely need lowered shocks as well. Ask me how I know. I have a great front set of brand new KYB's that I couldn't install.
Your shocks should be fine. I run/recommend stock length KYBs even with a 3" drop spring.
 

Latest posts

Forum statistics

Threads
41,857
Posts
903,628
Members
33,370
Latest member
mitchell1128
Top