700r4 stuck in 1st gear

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Toby

Junior Member
Joined
Jun 13, 2021
Posts
20
Reaction score
31
Location
Lompoc ca
First Name
Toby
Truck Year
1973
Truck Model
C10
Engine Size
350
I have a 700r4 attached to a cammed 350. The transmission is not shifting out of first gear. It’s holding on to the gear. Anyone have any idea what it is? I’m hoping it’s not in the need of a rebuild.
 

Vbb199

B-rate Hillbilly Customs
Joined
Jan 12, 2018
Posts
8,871
Reaction score
14,885
Location
Salisbury NC
First Name
Vince
Truck Year
89, 79
Truck Model
89 Suburban R1500, 79 C10
Engine Size
350, 502
Servo on the side of the trans could be leaking not allowing the band to grab/apply

Could be burnt band, burnt clutches.
Etc

TV cable properly set?
 

yevgenievich

Full Access Member
Joined
Mar 1, 2014
Posts
4,781
Reaction score
3,300
Location
Texas
First Name
Viktor
Truck Year
sad
Truck Model
very sad
Engine Size
less sad
Sticking tv cable common issue. While running pull the cable out few times then try driving and see if it will shift.
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,487
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Have you wound it all the way out in 1st gear and let off the throttle? Or does it just not shift while driving normally?
 

Toby

Junior Member
Joined
Jun 13, 2021
Posts
20
Reaction score
31
Location
Lompoc ca
First Name
Toby
Truck Year
1973
Truck Model
C10
Engine Size
350
I just drive it normally and it holds on to first.
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,487
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
If the governor is sticking, it won't shift until you wind it out. And then when it does shift, it may not go back into 1st (2nd gear start) until after it's been shut down for a few minutes.
 

JoeR Jr

Full Access Member
Joined
Jun 23, 2018
Posts
191
Reaction score
241
Location
Stokesdale, NC
First Name
Joe
Truck Year
1986
Truck Model
C10
Engine Size
6.0/4L80E
Maybe governor gear is stripped off and it isn't spinning. Lots of possibilities on that trans though.
Broken sun shell
2-4 band not applying
servo troubles
jammed valve body

just to name a few.
 

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,338
Reaction score
3,571
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
Does the trans have reverse? If so, the drive shell is fine. No reverse, 2nd or 4th gear, the drive shell is most likely stripped or broken.

I assume you have driven it pretty hard to see if it will shift? Put the shifter in “DRIVE” (not overdrive) Run it up to 25-30mph, let off the throttle. If it shifts, most likely the band or servo is at fault. The shift is caused by vehicle speed being high enough to skip 2nd gear, and going into 3rd. You don’t want to have the shifter in overdrive the band and servo are needed for 4th gear.

If it’s stuck in first gear, and has reverse, pull the govenor. Hopefully the gear is broken. If it’s stripped, inspect the bore the governor spins in, make sure it’s not chewed up. The gear stripped because for whatever reason the governor stopped turning. If the bore is chewed up, you probably need a new transmission case. They do make repair sleeves to fix the governor bore, but it takes some machine work to install. It’s probably cheaper just to find another case.
 

Mojave_Muse

Full Access Member
Joined
May 3, 2020
Posts
95
Reaction score
62
Location
California
First Name
crystal
Truck Year
1982
Truck Model
c10 Suburban
Engine Size
6.2
whilst all the above are good suggestions from people who likely know more about these than I do. I'll go with my first question, got enough trans fluid in it? just to eliminate the dumb stuff first.
 

Forum statistics

Threads
41,859
Posts
903,659
Members
33,372
Latest member
83elcowes
Top