I'm in need of help identifying Universal Joints.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Jonathonmb357

Full Access Member
Joined
Jan 13, 2022
Posts
91
Reaction score
77
Location
Fort Worth, Texas
First Name
Jonathon
Truck Year
1979
Truck Model
C30
Engine Size
292 cubic inch inline-six
I need some help with my 1979 C30. I's a cab and chassis with a 140" wheel base, and has a two-piece driveshaft.
The center U-joint is in terrible shape and has a boat load of play, and I need some help identifying it please. It will be my first time attempting to replace them so that will be fun!
It seems that the u-joints at the transmission and the differential are the same, but the center is different. I plan to try to replace all three, the carrier bearing, and the leaky pinion seal while I have it apart.
I appreciate any advice!
 

Attachments

  • 9A5C186B-0EC5-4BC7-B778-4AE216B61E77.jpeg
    9A5C186B-0EC5-4BC7-B778-4AE216B61E77.jpeg
    125.3 KB · Views: 73
  • 9CD77AD2-710C-438E-A66C-E09E341512EE.jpeg
    9CD77AD2-710C-438E-A66C-E09E341512EE.jpeg
    139.5 KB · Views: 69
  • 4B0B789D-D4C0-42A6-9454-DF1F163C61CA.jpeg
    4B0B789D-D4C0-42A6-9454-DF1F163C61CA.jpeg
    183.2 KB · Views: 69
  • 241D9DF5-8000-4D6A-A378-571D04775D0D.jpeg
    241D9DF5-8000-4D6A-A378-571D04775D0D.jpeg
    189.4 KB · Views: 67
  • 5203B6B4-B64E-4737-9D0A-830EB8F053B3.jpeg
    5203B6B4-B64E-4737-9D0A-830EB8F053B3.jpeg
    90.3 KB · Views: 78

CalSgt

Full Access Member
Joined
Oct 3, 2021
Posts
1,466
Reaction score
3,046
Location
CA
First Name
Casey
Truck Year
1980
Truck Model
Chevy K-10 Custom Deluxe
Engine Size
350
Best bet is to knock them out and bring them to the parts house with you to get replacements. Compare the cap diameter, width of the cross with caps installed, and what type of retaining clips the caps use. With new ones they sometimes seem too long from cap to cap, might have to push hard on the caps to hydraulic some grease out to compare them. Sometimes you might also have an option of greaseable or non greaseable joints.

ETA: U joints can be a real PIA if you've never done them before. Good hammer and set of impact sockets to use to drive them out helps. Also a large socket or something to use under the opposite side you are knocking through to allow the cap to be pushed out.
 

Snoots

Full Access Member
Joined
Jan 23, 2013
Posts
8,158
Reaction score
15,957
Location
Georgia
First Name
Roger
Truck Year
1973
Truck Model
Jimmy Sierra
Engine Size
350
Spend the extra $ for greaseable. And use only bearing grease!
 

LateOnTheBrakes

5.3-Swapped 86 CUCV
Joined
Feb 2, 2020
Posts
463
Reaction score
123
Location
Virginia
First Name
Joshua
Truck Year
1986
Truck Model
CUCV
Engine Size
5.3
I don't know that you are going to identify them without removing/measuring them. You need a set of calipers to get the cap diameters and the distance from one cap to another. Then look for a cross reference from your company of choice.
 

Attachments

  • Spicer U Joints.pdf
    224.5 KB · Views: 158
  • Spicer OSR Measurements.pdf
    95.5 KB · Views: 79
  • Spicer Yoke Measurement.pdf
    962.6 KB · Views: 107

84c10Tony

Howdy!
Joined
Apr 14, 2017
Posts
141
Reaction score
119
Location
So Cal
First Name
Tony
Truck Year
84
Truck Model
c10
Engine Size
305
Had my little SR5 driveshaft redone years ago when having the original clutch replaced at around 190k. In my mind, I wanted it super strong to last, so went with Rockcrawlers super heavy duty u-joints instead of Toyota OEM.
What I did not know to check, was specs, the heavy duty joints were about 3 ten thousands of "play" where the OEM was 1 tenth, the message I got when shaft was rebuilt, "these will last 25k miles", uh huh, hmm, too late...
The super heavy duty looked twice as thick which was cool, the extra play, not so much. Sure enough, 25k and it tore up the center shaft bearing. The truck was not riding smooth, and had vibrations at different speeds.
When having the rear diff seal replaced, I had the shop install my new OEM joints (which were sitting here in my boxes of new oem parts waiting on my hobby for future fun!) and re-balanced. Rides smooth as silk now.
A lesson learned, I was not trying to be cheap, but to make it stronger, and missed an important point.

Note, after an accident, I am no longer able to do these fun things as my hobby, so...off to the shops to install my boxes of parts when needed, $$$$ ouch...
So remember to appreciate and enjoy having the Ability to do stuff...and "Get er' done"!
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,904
Reaction score
7,249
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
Should be a 1350, if I’m not mistaken. The lifetime spicer joints supposed to be the strongest and highest quality, but are not greasable.

On the lifetime joints, when you pull the caps to install the new joints, do not mix up which cap came from where. They need to go back onto the same trunnion they came off of. Also, learn from my boneheadedness, when you press or beat them out, it’s not a bad idea to have a piece of pipe or other metal to wedge between the ears of the yoke so you don’t squeeze them together on accident. Some people cut the cross out to avoid pressing two caps out at once (less force required).
 
Last edited:

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,956
Reaction score
23,465
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Should be a 1350, if I’m not mistaken. The lifetime spicer joints supposed to be the strongest and highest quality, but are not greasable.

On the lifetime joints, when you pull the caps to install the new joints, do not mix up which cap came from where. They need to go back onto the same trunnion they came off of. Also, learn from my boneheadedness, when you press or beat them out, it’s not a bad idea to have a piece of pipe or other metal to wedge between the ears of the yoke so you don’t squeeze them together on accident. Some people cut the cross out to avoid pressing two caps out at once (less force required).

Right, they should all be 1350 joints.
 

Doppleganger

Full Access Member
Joined
May 24, 2019
Posts
11,599
Reaction score
53,641
Location
OH-MI: Just like it sounds
First Name
Chris
Truck Year
1985
Truck Model
K20
Engine Size
5.7
I went through this a couple years ago - no one at Moog seemed to know what fit so I have a pile of new U-joints in the box that will fit someone's truck.....just not mine.

Like Sgt said.....remove old, take with, and get what matches.
 

Jonathonmb357

Full Access Member
Joined
Jan 13, 2022
Posts
91
Reaction score
77
Location
Fort Worth, Texas
First Name
Jonathon
Truck Year
1979
Truck Model
C30
Engine Size
292 cubic inch inline-six
Best bet is to knock them out and bring them to the parts house with you to get replacements. Compare the cap diameter, width of the cross with caps installed, and what type of retaining clips the caps use. With new ones they sometimes seem too long from cap to cap, might have to push hard on the caps to hydraulic some grease out to compare them. Sometimes you might also have an option of greaseable or non greaseable joints.

ETA: U joints can be a real PIA if you've never done them before. Good hammer and set of impact sockets to use to drive them out helps. Also a large socket or something to use under the opposite side you are knocking through to allow the cap to be pushed out.
Thank you! I appreciate it man
 

Jonathonmb357

Full Access Member
Joined
Jan 13, 2022
Posts
91
Reaction score
77
Location
Fort Worth, Texas
First Name
Jonathon
Truck Year
1979
Truck Model
C30
Engine Size
292 cubic inch inline-six
I went through this a couple years ago - no one at Moog seemed to know what fit so I have a pile of new U-joints in the box that will fit someone's truck.....just not mine.

Like Sgt said.....remove old, take with, and get what matches.
Spend the extra $ for greaseable. And use only bearing grease!
Alright, definitely noted down! Thanks a bunch
 

Jonathonmb357

Full Access Member
Joined
Jan 13, 2022
Posts
91
Reaction score
77
Location
Fort Worth, Texas
First Name
Jonathon
Truck Year
1979
Truck Model
C30
Engine Size
292 cubic inch inline-six
I don't know that you are going to identify them without removing/measuring them. You need a set of calipers to get the cap diameters and the distance from one cap to another. Then look for a cross reference from your company of choice.
Okay! Thank you very much
 

Jonathonmb357

Full Access Member
Joined
Jan 13, 2022
Posts
91
Reaction score
77
Location
Fort Worth, Texas
First Name
Jonathon
Truck Year
1979
Truck Model
C30
Engine Size
292 cubic inch inline-six
Had my little SR5 driveshaft redone years ago when having the original clutch replaced at around 190k. In my mind, I wanted it super strong to last, so went with Rockcrawlers super heavy duty u-joints instead of Toyota OEM.
What I did not know to check, was specs, the heavy duty joints were about 3 ten thousands of "play" where the OEM was 1 tenth, the message I got when shaft was rebuilt, "these will last 25k miles", uh huh, hmm, too late...
The super heavy duty looked twice as thick which was cool, the extra play, not so much. Sure enough, 25k and it tore up the center shaft bearing. The truck was not riding smooth, and had vibrations at different speeds.
When having the rear diff seal replaced, I had the shop install my new OEM joints (which were sitting here in my boxes of new oem parts waiting on my hobby for future fun!) and re-balanced. Rides smooth as silk now.
A lesson learned, I was not trying to be cheap, but to make it stronger, and missed an important point.

Note, after an accident, I am no longer able to do these fun things as my hobby, so...off to the shops to install my boxes of parts when needed, $$$$ ouch...
So remember to appreciate and enjoy having the Ability to do stuff...and "Get er' done"!
I definitely will! Thank you
 

Jonathonmb357

Full Access Member
Joined
Jan 13, 2022
Posts
91
Reaction score
77
Location
Fort Worth, Texas
First Name
Jonathon
Truck Year
1979
Truck Model
C30
Engine Size
292 cubic inch inline-six
Should be a 1350, if I’m not mistaken. The lifetime spicer joints supposed to be the strongest and highest quality, but are not greasable.

On the lifetime joints, when you pull the caps to install the new joints, do not mix up which cap came from where. They need to go back onto the same trunnion they came off of. Also, learn from my boneheadedness, when you press or beat them out, it’s not a bad idea to have a piece of pipe or other metal to wedge between the ears of the yoke so you don’t squeeze them together on accident. Some people cut the cross out to avoid pressing two caps out at once (less force required).
Thanks man! I appreciate it
 

Latest posts

Forum statistics

Threads
41,848
Posts
903,424
Members
33,362
Latest member
Dhatch84
Top