1991 suburban project

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Daveo91Burb

Full Access Member
Joined
Jul 6, 2014
Posts
663
Reaction score
229
Location
Vancouver, WA
First Name
Dave
Truck Year
1991
Truck Model
V2500 Silverado Suburban
Engine Size
Vortec 383, modified TBI/4L80e
Welcome fellow '91 Burb owner! 383 with vortec heads in mine, but the LS conversion was on my mind (and still is sometimes) when I was building my SBC.
 

3FingerDan

Junior Member
Joined
Apr 12, 2021
Posts
4
Reaction score
18
Location
Missouri
First Name
Dan
Truck Year
1991
Truck Model
Suburban
Engine Size
5.7
Great project start. That is great news after starting with 3yo gas in it. How much gas is in it now? I'm wondering if it might be a good idea to top off with 91 octane or whatever you can get without ethanol and run it out.

So let's hear the story about 3 fingers. So what happened that you lost a few??? We're open and honest like family here, so don't be shy. Spill it. I see 4 fingers and a thumb on the Left hand, so it must be the right hand missing some digits.

I'd fire up a build thread in the Under Construction section and document your progress while getting help, ideas, suggestions and opinions along the way.

The finger story- short version- I do industrial/heavy commercial mechanical work (heating/cooling/industrial process piping). I was working at a hospital on a large air handler and was moving belts by hand on a large fan (fan wheel was steel and about 6-700lbs with a 75hp electric motor). Being 21 and oblivious, my hand ran through the worn-razor-sharp motor pulley while checking motor bearings and got the end knuckles of 3 fingers. Wrapped the hand in my over shirt and walked down to the ER. Luckily, they were mostly saved and didn’t suffer any problems long term with the hand. But, my nickname was born that day. I’m 36 now and still am known by everyone as three finger Dan. It sucks it happened, but has shaped how I view paying attention/doing things safely.

Back to the suburban though, I filled it with 10 gallons of 93 ethanol free premium and will see how it does. It was pretty much empty, which isn’t a good thing as moisture and rust is probably in the tank. We’ll see how it does, but I see a new tank in it’s future.

I’m about to start a thread in the other forum you mentioned. Bought a parts truck today with 3/4 ton axles, so I have some plans.

Thanks for the warm welcome everyone!
 

HotRodPC

Administrator
Staff member
Admin
Joined
Aug 29, 2010
Posts
47,014
Reaction score
9,010
Location
OKC, OK
First Name
HotRod
Truck Year
85 K20 LWB
Truck Model
Silverado
Engine Size
454 - Turbo 400 - 3.73
The finger story- short version- I do industrial/heavy commercial mechanical work (heating/cooling/industrial process piping). I was working at a hospital on a large air handler and was moving belts by hand on a large fan (fan wheel was steel and about 6-700lbs with a 75hp electric motor). Being 21 and oblivious, my hand ran through the worn-razor-sharp motor pulley while checking motor bearings and got the end knuckles of 3 fingers. Wrapped the hand in my over shirt and walked down to the ER. Luckily, they were mostly saved and didn’t suffer any problems long term with the hand. But, my nickname was born that day. I’m 36 now and still am known by everyone as three finger Dan. It sucks it happened, but has shaped how I view paying attention/doing things safely.

Back to the suburban though, I filled it with 10 gallons of 93 ethanol free premium and will see how it does. It was pretty much empty, which isn’t a good thing as moisture and rust is probably in the tank. We’ll see how it does, but I see a new tank in it’s future.

I’m about to start a thread in the other forum you mentioned. Bought a parts truck today with 3/4 ton axles, so I have some plans.

Thanks for the warm welcome everyone!
Great, I'll be looking for the build thread.

At least you're a male, so 3 finger Dan isn't so bad. Back in the day there was this girl that everyone had a turn with. They called her 4 Finger Barbara and I'm here to tell you, I think that was being conservative cuz I think it should have been full ****** Barbara. It's just a real good thing she could get that golf ball through a garden hose or there wouldn't have been anything at all worthy.

That sounds pretty damn painful. I've dealt with some of that duct work and that is some sharp stuff, so you don't even need to be playing in wheels and motors in that biz to get sliced open and gutted like a fish.
 

R Carnella

Supporting Member
Supporting Member
Joined
Sep 21, 2017
Posts
359
Reaction score
753
Location
Long island
First Name
Rich
Truck Year
1990
Truck Model
Suburban V2500
Engine Size
5.3
Welcome fellow burb lover,so much potential in these trucks I'm looking forward to seeing what you do with it.
I looks very similar to my 1990 v2500 when i brought it home. I have since fully disassembled and reassembled to my liking lol.

You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
 

Green76K10

Junior Member
Joined
May 11, 2022
Posts
1
Reaction score
1
Location
NorCal
First Name
Mark
Truck Year
1976
Truck Model
k10
Engine Size
350
This is my 1976 k10. Just dropped in a new 350. 4" lift. Still working on her.
 

Attachments

  • 20220429_101945.jpg
    20220429_101945.jpg
    365.5 KB · Views: 34
  • 20220510_125841.jpg
    20220510_125841.jpg
    207.2 KB · Views: 41

Latest posts

Forum statistics

Threads
42,104
Posts
909,138
Members
33,586
Latest member
ssgmike
Top