Vince's TBI woes, progressive revelations, and tbi mods.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Chevyguy

Full Access Member
Joined
Sep 10, 2012
Posts
185
Reaction score
60
Location
Eugene,OR
First Name
Clayton
Truck Year
1987
Truck Model
V20
Engine Size
5.7 Litre
So, last night @Chevyguy @gmbellew i installed the new TPS, mounting holes were .200", i drilled them to .250 for wiggle room. Set it at like, .60V at idle...WOT was coming up as 4.5...

Same gig as before though, harness unplugged, i had 4.97v, plugged into TPS, i got 4.5v......

Suggestions? I assumed thr range of 4.5-5.0v wot was acceptable?
Should be at .45 to .50 at idle. Mine is at .50 at idle.

Clayton

Sent from my SM-A705U using Tapatalk
 

Chevyguy

Full Access Member
Joined
Sep 10, 2012
Posts
185
Reaction score
60
Location
Eugene,OR
First Name
Clayton
Truck Year
1987
Truck Model
V20
Engine Size
5.7 Litre
So, last night @Chevyguy @gmbellew i installed the new TPS, mounting holes were .200", i drilled them to .250 for wiggle room. Set it at like, .60V at idle...WOT was coming up as 4.5...

Same gig as before though, harness unplugged, i had 4.97v, plugged into TPS, i got 4.5v......

Suggestions? I assumed thr range of 4.5-5.0v wot was acceptable?
You look good at wide open throttle.

Sent from my SM-A705U using Tapatalk
 

Big Chip

Full Access Member
Joined
Oct 19, 2017
Posts
4,656
Reaction score
6,728
Location
Michigan
First Name
Kevin
Truck Year
1979
Truck Model
C35
Engine Size
454
The pull was from in drive, foot on brake, then accelerating to 81mph, then a gradual decrease in vehicle speed back down to a slow speed to make a right turn.

Im open your suggestions.

My first thought was to take that junk right up to 88mph, go back in time and take care of it a little better, take it back up to 88mph, come back to the future and just enjoy your sweet trouble-free rig.

Maybe next time.
 

gmbellew

Full Access Member
Joined
May 27, 2018
Posts
1,036
Reaction score
1,020
Location
Kansas city
First Name
glen
Truck Year
1990
Truck Model
suburban 1500
Engine Size
350
i checked my TPS today. at idle it is .66v and WOT using the skinny pedal is 1.45v (edit - 4.45v). i didn't go under the hood and check with the linkage.

WOT voltage is good. idle voltage is a little higher than I'd like, but not crazy. maybe if it ever warms up, i will drop a new one in. although the truck runs well, and i always hate to mess with something that is working...
 
Last edited:

Chevyguy

Full Access Member
Joined
Sep 10, 2012
Posts
185
Reaction score
60
Location
Eugene,OR
First Name
Clayton
Truck Year
1987
Truck Model
V20
Engine Size
5.7 Litre
i checked my TPS today. at idle it is .66v and WOT using the skinny pedal is 1.45. i didn't go under the hood and check with the linkage.

WOT voltage is good. idle voltage is a little higher than I'd like, but not crazy. maybe if it ever warms up, i will drop a new one in. although the truck runs well, and i always hate to mess with something that is working...
Your wide open throttle voltage ought to be closer to 4.5-5 volts. You need a new TPS.

Clayton

Sent from my SM-A705U using Tapatalk
 

Chevyguy

Full Access Member
Joined
Sep 10, 2012
Posts
185
Reaction score
60
Location
Eugene,OR
First Name
Clayton
Truck Year
1987
Truck Model
V20
Engine Size
5.7 Litre
sorry, typo. it was 4.45....
You're good to go at WOT then. I still think your TPS may need replacement due to the higher than specifications voltage at closed throttle.

Clayton

Sent from my SM-A705U using Tapatalk
 

1987 GMC Jimmy

Automobile Hoarder
Joined
Jan 23, 2016
Posts
5,848
Reaction score
2,387
Location
Mississippi
First Name
Jesse
Truck Year
1987
Truck Model
V1500 Jimmy
Engine Size
350
A few thoughts...

One, that resting TPS value is too high, and I don’t think it can be remedied with the current sensor. You can always try, but I think the cheapo ones rest at about at .66V, and I adjusted that down to .59V by boring the holes and slightly clocking the sensor. I wouldn’t worry too much about the high side because the carpet being an obstruction to the gas pedal is a very real thing. You can always get it close to the upper end when you’re working the throttle manually. Also, is everything okay with the grounds? I’ve seen a missing engine to firewall strap throw a TPS code.

Two, is the idle screw still sealed on your TBI unit? Not trying to beat a dead horse, but the idle’s a bit too high even when it’s warmed up. The IACV counts seem a tad high, but I wouldn’t run to replace the thing just yet. Making sure the sensor pintle is clean, the air passages underneath are clean, and doing a relearn could help in that situation in conjunction with getting that TPS voltage down. It looks like the lowest you ever got was 51 counts. That’s not terrible, but I think I sit at 40 steps in a warm, parked idle at roughly 800 RPM. In drive, warm I sit at 0 with an engine speed of about 600 RPM. 20-50 is the ballpark range you want it to settle to in park, but it ultimately depends on the vehicle.

Three, what’s your vacuum, like 22” you said? That’s really good, and the MAP sensor confirms. Just out of curiosity, what’s your approximate altitude there?

Four, I wouldn’t pay a lot of mind to the TPS calculations. The BLM/INT look fine, and I don’t see an injector duty cycle calculation, but that’s the one that gives me totally ridiculous feedback.

I think that’s all I have.
 

Vbb199

B-rate Hillbilly Customs
Joined
Jan 12, 2018
Posts
8,871
Reaction score
14,885
Location
Salisbury NC
First Name
Vince
Truck Year
89, 79
Truck Model
89 Suburban R1500, 79 C10
Engine Size
350, 502
A few thoughts...

One, that resting TPS value is too high, and I don’t think it can be remedied with the current sensor. You can always try, but I think the cheapo ones rest at about at .66V, and I adjusted that down to .59V by boring the holes and slightly clocking the sensor. I wouldn’t worry too much about the high side because the carpet being an obstruction to the gas pedal is a very real thing. You can always get it close to the upper end when you’re working the throttle manually. Also, is everything okay with the grounds? I’ve seen a missing engine to firewall strap throw a TPS code.

Two, is the idle screw still sealed on your TBI unit? Not trying to beat a dead horse, but the idle’s a bit too high even when it’s warmed up. The IACV counts seem a tad high, but I wouldn’t run to replace the thing just yet. Making sure the sensor pintle is clean, the air passages underneath are clean, and doing a relearn could help in that situation in conjunction with getting that TPS voltage down. It looks like the lowest you ever got was 51 counts. That’s not terrible, but I think I sit at 40 steps in a warm, parked idle at roughly 800 RPM. In drive, warm I sit at 0 with an engine speed of about 600 RPM. 20-50 is the ballpark range you want it to settle to in park, but it ultimately depends on the vehicle.

Three, what’s your vacuum, like 22” you said? That’s really good, and the MAP sensor confirms. Just out of curiosity, what’s your approximate altitude there?

Four, I wouldn’t pay a lot of mind to the TPS calculations. The BLM/INT look fine, and I don’t see an injector duty cycle calculation, but that’s the one that gives me totally ridiculous feedback.

I think that’s all I have.


1. I have bored the holes out on the replacement unit, i just had never adjusted it. It wasnt the bottom dollar unit. i think.... standard ignition was the name? Theyre american made i believe. I DID notice since i pulled the trans out, a harness strap is broken. But as you know, there are many straps on the harness, but i probably need that 1 working .

2. Yes, ive reset the idle thru the proper proceedure several times. I have a leak somewhere or something causing that high idle. IAC has been replaced maybe.. 10 months ago now? Idle was high even when i first got the shitbox from its tree-side grave.

3. Yes, the motor makes 22 in/hg at the front of the throttle body, but my map kPa readings are low? 26-28 kPa is like an avg. Of 8 in/hg?? I dont follow where you are going. As far as approx altitude, the internet says we are 791' above. I kmow they are not directly related, but i personally do not know in what capacity they are related, if that makes sense.



4. Those calculations are indeed retarded. I contacted the app developer, he said that was a defunct .adx file (used for communication with ecm), he said at my current voltage at idle, its more like a 18% load. He sent another .adx, but i didnt install it.


All of this is good data, for sure. Im just as suspicious of grounds, and as i said, im gonna look into that broken ground, AND the ground running from motor to the cab. If i remember correctly, that strap is.... on the passenger side? Of the firewall? I will look into engine straps.... still in transmission mode at the moment. I just got the pos put back together last night.
 
Last edited:

Urbanburban22

Junior Member
Joined
Apr 22, 2022
Posts
23
Reaction score
21
Location
Colorado
First Name
David
Truck Year
1991
Truck Model
Suburban SLE V1500
Engine Size
5.7 TBI
Im patiently waiting on a new PROM chip for my truck... will boost hp and tq 35 points min as well as delete the egr circuit, following that ill block it off with a plate i machine up.........

Im not giving it a whole lot if thought until the chip arrives.... but your thoughts are on track with mine there.
you can get chips? What exactly is PROM? How/where could I find the right chip for a 91 tbi?
 

Vbb199

B-rate Hillbilly Customs
Joined
Jan 12, 2018
Posts
8,871
Reaction score
14,885
Location
Salisbury NC
First Name
Vince
Truck Year
89, 79
Truck Model
89 Suburban R1500, 79 C10
Engine Size
350, 502
you can get chips? What exactly is PROM? How/where could I find the right chip for a 91 tbi?


I had a guy online burn one for me, but ive since found another guy who has moates and PROM burning capability.

PROM contains the programmable parameters for the PCM
 

Forum statistics

Threads
41,858
Posts
903,637
Members
33,371
Latest member
Linemanjl
Top