Cab swap?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

79K15 HIghSierra

Full Access Member
Joined
Nov 19, 2020
Posts
83
Reaction score
175
Location
South Carolina
First Name
Reuben
Truck Year
1979
Truck Model
K1500
Engine Size
350
Wanting to get a new cab for my 79 k15, mines a bit rusty. Problem is, all I can find used around me are 81-87 cabs. Would that have significant issues with swapping? Thanks! also mine is 4 speed floor shifter so I’m planning on having to make that mod unless I can find a manual trans cab.
 

jjester6000

Full Access Member
Joined
Aug 24, 2019
Posts
878
Reaction score
2,444
Location
Illinois
First Name
Jack
Truck Year
1974
Truck Model
C1500
Engine Size
250
Wanting to get a new cab for my 79 k15, mines a bit rusty. Problem is, all I can find used around me are 81-87 cabs. Would that have significant issues with swapping? Thanks! also mine is 4 speed floor shifter so I’m planning on having to make that mod unless I can find a manual trans cab.

It should pretty much bolt right up to the body mounts, and doors but you might have to drill a couple of holes and stuff to mount the dash, pedals, and maybe the fenders, but many have done the swap in the past.
(I've never done the swap myself, but I assume that any differences can be taken care of pretty easilly)

I'd just cut the trans tunnel out of your old cab and weld, screw, or rivet it in place in then new cab to make it all work.
 

SDJunkMan

Full Access Member
Joined
Nov 17, 2017
Posts
1,792
Reaction score
2,627
Location
Black Hills of South Dakota
First Name
Jeff
Truck Year
1978
Truck Model
K10
Engine Size
350
I think putting a early clip on a late cab is ok, harder to go the other way because of the hood hinges. Everything else should be a direct fit (I hope so, cause I plan to put a late cab on my 80).
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,956
Reaction score
23,465
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
The cabs are basically the same. There will be extra holes leftover in the upper cowl panel from the hood hinges and seals. The top bolt holes on the fenders will need opened up some because the bolt holes are slightly more inboard on the newer cabs. New bolt holes will need drilled for the wiper posts. There will be speaker openings on the dash corners where dash pad clips are supposed to go. '84-up cabs will not have the opening in the dash for the wiper switch and the headlight switch will be in a different location because of that.

There's probably a couple more minor details I'm forgetting.
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
2,837
Reaction score
6,352
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
It will work. Need the wiper drive from the round eye. The mounts are longer on the newer front. The top of the fenders on the cab mount don't sit perfect, but they are close. Like @bucket stated, slight mod needed.

Save your floor trans cover. You will need a piece of the floor behind it as well if the cab you get is from a 2 wheel drive. Cut the floor before you attempt to set the cab on the frame.
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
2,837
Reaction score
6,352
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
Depending on the years swapped you may need the taller rear body mounts too.
 

Ken B

Full Access Member
Joined
Sep 18, 2019
Posts
1,061
Reaction score
1,242
Location
indiana
First Name
ken
Truck Year
81
Truck Model
c10
Engine Size
250
Good Information, I just bought a donor vehicle for just such a swap.
 

Latest posts

Forum statistics

Threads
41,848
Posts
903,425
Members
33,362
Latest member
Dhatch84
Top