Project: 83 C30 Crew Cab Big Brown Turd

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
Can you post a picture of the front spindles?

Spindles showed up in a pretty trashed box.

Pulled them out and one of them has a pretty good ding in it, I think that is where the grease seal is supposed to sit...

You must be registered for see images attach
You must be registered for see images attach

You must be registered for see images attach
You must be registered for see images attach

You must be registered for see images attach
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
What’s the srw rear end for?
Narrower axle width to make room for the wider tire setup and keeping them inside the fender wells?
What is the width difference between 14bolt srw/drw?

Yes sir, the dually rear end is 72" WMS to WMS (wheel mounting surface) and the SRW 14B is 67" WMS to WMS

This is supposed to allow the 22" Alcoas to tuck under the stock fenders using the 8x10 adapters. We will see what happens!
 

wanderinthru

Full Access Member
Joined
Jul 23, 2020
Posts
1,170
Reaction score
2,046
Location
Mid Point Route 66
First Name
Shakey
Truck Year
81, 70, 75, 84, 89
Truck Model
K 10, C 30, K 20
Engine Size
350
Maybe it's the picture, but that seal journal looks awful rough? Also looks cast? Personally I wouldnt want a seal to run on cast, much less rough cast. Or does the seal press to the spindle and run on the hub?
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
Maybe it's the picture, but that seal journal looks awful rough? Also looks cast? Personally I wouldnt want a seal to run on cast, much less rough cast. Or does the seal press to the spindle and run on the hub?

I think that is just the photo not really showing it too well. It is a machined surface. I am more concerned with the big ol din in it.
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
The new (old) SRW rear end will be getting new brakes and lines, cleaned up and maybe shot in epoxy prior to installation.

You must be registered for see images attach
 

Craig 85

Full Access Member
Joined
Jan 25, 2017
Posts
3,889
Reaction score
4,024
Location
Nashville, TN
First Name
Craig
Truck Year
1985
Truck Model
K30 SRW
Engine Size
454/TH-400/NP205
Question, are you keeping those 11" drums or can they be changed out for the 13" from the Dana 70 that was in the truck? I don't know if the drums and backing plates are compatible from the 70 to the 14 FF, just throwing it out there. Here's a picture of the 13x3.5" I have on my K30 SRW for reference.

You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
 

Big Chip

Full Access Member
Joined
Oct 19, 2017
Posts
4,656
Reaction score
6,728
Location
Michigan
First Name
Kevin
Truck Year
1979
Truck Model
C35
Engine Size
454
Looks like you got belltech spindles so you’ll run into the same problem I have. I was hoping they would have sent you a different brand so I could see if the steering arm was lower in relation to the spindle.
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
What’s the srw rear end for?
Narrower axle width to make room for the wider tire setup and keeping them inside the fender wells?
What is the width difference between 14bolt srw/drw?

Grit Dog, yes the SRW is 67" vs the DRW 72" WMS to WMS (wheel mounting surface) and the idea is to keep the tires tucked under stock outer fenders. The bed fenders will be widened by 4"
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
Looks like you got belltech spindles so you’ll run into the same problem I have. I was hoping they would have sent you a different brand so I could see if the steering arm was lower in relation to the spindle.

Big Chip, what problem did you have with the Bell Tech Spindles? And yes, mine are definitely Bell Techs.
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
Well this showed up today and it's not even Christmas.

And yes I do make my kids hold up my purchases for my toys. That way I know that I will have photos of my kids.

Toyo 265/35-22s are on the way!

You must be registered for see images attach
You must be registered for see images attach

You must be registered for see images attach

265/35-22 Toyos should be here in a day or two
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
Question, are you keeping those 11" drums or can they be changed out for the 13" from the Dana 70 that was in the truck? I don't know if the drums and backing plates are compatible from the 70 to the 14 FF, just throwing it out there...

Sticking with the SRW drums, should be fine for what I'm doing, towing around a couple of German Shepherds and my wakeboard boat occasionally.
 

OldFatBald

Full Access Member
Joined
Aug 27, 2020
Posts
85
Reaction score
102
Location
Northern California
First Name
Eric
Truck Year
1983
Truck Model
C30
Engine Size
454
My brown bed floor was pretty abused, so I picked this one up kinda locally.

Mounted it last night, it still sits a little low on the passenger's side.

I have a replacement front bed panel that I put in epoxy primer last night. Going to mount it this weekend and see if it pulls that side up some. The driver's side lines up quite well.

The C30's frame is is very good shape, I had a buddy check it and make some minor adjustments on his frame machine.

You must be registered for see images attach
You must be registered for see images attach
 

Big Chip

Full Access Member
Joined
Oct 19, 2017
Posts
4,656
Reaction score
6,728
Location
Michigan
First Name
Kevin
Truck Year
1979
Truck Model
C35
Engine Size
454
Big Chip, what problem did you have with the Bell Tech Spindles? And yes, mine are definitely Bell Techs.
You have to rotate the tie rod end 180° and install from the bottom up which means you can’t use stock alignment specs. There’s also a bump steer issue when you change the tie rod position. You can also see that a left turn creates an interference problem with the tie rod and pitman arm. To me it seems like the steering arm on the spindle is too high. It should be lower in relation to the spindle centerline. I was hoping you had a different brand so I could compare them.
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
 

Latest posts

Forum statistics

Threads
41,853
Posts
903,554
Members
33,366
Latest member
texdave
Top