Seeking 7.5” 10 Bolt Advice...

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

1987 GMC Jimmy

Automobile Hoarder
Joined
Jan 23, 2016
Posts
5,848
Reaction score
2,387
Location
Mississippi
First Name
Jesse
Truck Year
1987
Truck Model
V1500 Jimmy
Engine Size
350
At almost 300K miles, the Corp. 10 in my car is singing its swan song. I’m going to try and make it a little longer, but it’s time to start planning what I’m going to do after. Ideally, I’d just keep the current axle since it has the control arm ears and the spring perches. As it stands, it’s a 2.56 ratio, 28 spline (I think) and open. The ratio doesn’t bother me as much because it has good highway manners, but the lack of positraction sucks. In a perfect world, I’d get a 9C1 8.5” that already has 3.23 gears and the Eaton G80. Not the gold standard in limited slip but okay for what I do/need. People want too much for the whole setup, and they don’t seem to be very available.

Realistically, it seems like I’ll have to get a MotiveGear master kit for the 7.5”, $260, a posi setup, expensive, and then send it all to the builder. I’ll be $6-700 in the whole before labor, which seems unreal to me. If anyone can recommend a good posi unit, aside from Eaton, for the 7.5”, I would appreciate it. I’ve seen several brands that ring a bell, but I don’t know their quality. Also, if anyone has any suggestions or leads on a compatible 8.5” or even a 12 Bolt, I’m open to any input. I’m assuming a 12 would be from an old Bel Air, Biscayne, Caprice, etc., and then my only options on the 8.5” are a 9C1 Caprice or a hot G Body. Maybe an F Body?

I’m better than I used to be, but I don’t pretend to be an expert on these enigmatic pumpkins.
 

The88

Mhmm
Joined
Dec 9, 2015
Posts
1,074
Reaction score
1,363
Location
South Louisiana
First Name
ThatGuy
Truck Year
88
Truck Model
K5
Engine Size
5.7
Check with Quick Performance. They have good prices and the guys there are knowledgeable. I have bought from them a couple times.

I know a gear guy that shouldn't be that steep for install to your west. If you were interested.
 

1987 GMC Jimmy

Automobile Hoarder
Joined
Jan 23, 2016
Posts
5,848
Reaction score
2,387
Location
Mississippi
First Name
Jesse
Truck Year
1987
Truck Model
V1500 Jimmy
Engine Size
350
I’ll look them up when I get home, and I’ll take any references, too. Feel free to share here, or if you wanna PM me, that works.
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,966
Reaction score
23,489
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
I didn't realize they even put a 7.5 in some B-body cars.

Is the 5x4.75 bolt pattern a must? And if so, are you willing to have 5x5 axle redrilled for 4.75?
 

Curt

Full Access Member
Joined
Sep 11, 2017
Posts
676
Reaction score
1,140
Location
Loco Hills
First Name
Curt
Truck Year
1984
Truck Model
K-30
Engine Size
383
I think you should try to rebuild the unit yourself.A few tools from Harbor Freight.There’s a massive amount of knowledge on YouTube.I rebuilt my first axle a few months ago.I wish I could say it was all peachy,but there was a few hiccups.However,determination and help from the internet put me over the line.
 

Curt

Full Access Member
Joined
Sep 11, 2017
Posts
676
Reaction score
1,140
Location
Loco Hills
First Name
Curt
Truck Year
1984
Truck Model
K-30
Engine Size
383
By the way,Eaton is an amazing company with amazing products.It’s a safe bet.
 

1987 GMC Jimmy

Automobile Hoarder
Joined
Jan 23, 2016
Posts
5,848
Reaction score
2,387
Location
Mississippi
First Name
Jesse
Truck Year
1987
Truck Model
V1500 Jimmy
Engine Size
350
I didn't realize they even put a 7.5 in some B-body cars.

Is the 5x4.75 bolt pattern a must? And if so, are you willing to have 5x5 axle redrilled for 4.75?

Sorry for the belated response. You thought they came with 8.5s or... So what you’re saying is my current wheels are a no-go if I went from 7.5 to 8.5 unless I redrilled?
 

CorvairGeek

Full Access Member
Joined
May 7, 2012
Posts
548
Reaction score
908
Location
Boise
First Name
Jerry
Truck Year
1978
Truck Model
C20 Scottsdale
Engine Size
292 L6, T400
7.5 axles are all 4.75 pattern while 8.5s were available in both, IIRC.
 

Rusty Nail

Full Access Member
Joined
Jan 29, 2015
Posts
9,735
Reaction score
9,534
Location
the other side of the internet
First Name
Rusty
Truck Year
1977
Truck Model
C20
Engine Size
350sbc
7.5 axles are all 4.75 pattern while 8.5s were available in both, IIRC.

That sounds right CGeek and I also want to agree with Curt.

My first thought involved not spending one dime in a 7.5...
F body axles are too narrow I bet.

Your pretty good with the wrenches man...why don't you do it yourself? Screw spendin all that money right now!
Besides when you'ree finished you could tell the rest of us how. :D
Might even learn somthin.

AND THEN ?

and then think of all the possibilities. ;)
 

Latest posts

Forum statistics

Threads
41,859
Posts
903,665
Members
33,372
Latest member
83elcowes
Top