Adding convertor (s). Yes, I said adding.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
3,658
Reaction score
6,597
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
Well ****! The Magnaflo rep tells me that the convertor must reach a minimum of 350 degrees to "light off".

My K20 has long tube headers and true dual 2.25" pipes. After crawling under it tonight, I realized there is no way on Gods green Corona virus infested earth that a cat is going to fit before the cross member.

Soo, I brought home a thermal temp gun from work and measured the pipes temp from the exhaust ports all the way to the rear axle.

Using long tube headers, the cat would have to essentially be connected to the header flange. It barely reached 350 degrees at that point. At the cross member where I have plenty of room, it barely got to 150.

I drove the truck and got the engine to temp (195) and let it idle during all the testing.

Just to be sure the readings were accurate, I took measurements with the temp probe on my Fluke multimeter. Same....:(

So I guess I'm **** out of luck. I'll have to rely on tuning the efi to get it the best I can.
 

roundhouse

Full Access Member
Joined
Apr 5, 2014
Posts
669
Reaction score
527
Location
atlanta ga
First Name
justin
Truck Year
77,78,79,80 ?
Truck Model
K10
Engine Size
350
Well ****! The Magnaflo rep tells me that the convertor must reach a minimum of 350 degrees to "light off".

My K20 has long tube headers and true dual 2.25" pipes. After crawling under it tonight, I realized there is no way on Gods green Corona virus infested earth that a cat is going to fit before the cross member.

Soo, I brought home a thermal temp gun from work and measured the pipes temp from the exhaust ports all the way to the rear axle.

Using long tube headers, the cat would have to essentially be connected to the header flange. It barely reached 350 degrees at that point. At the cross member where I have plenty of room, it barely got to 150.

I drove the truck and got the engine to temp (195) and let it idle during all the testing.

Just to be sure the readings were accurate, I took measurements with the temp probe on my Fluke multimeter. Same....:(

So I guess I'm **** out of luck. I'll have to rely on tuning the efi to get it the best I can.
You could use some short tube headers
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,904
Reaction score
7,249
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
xc_hide_links_from_guests_guests_error_hide_media
 

SirRobyn0

Full Access Member
Joined
Dec 6, 2019
Posts
6,698
Reaction score
11,151
Location
In the woods in Western Washington
First Name
Rob
Truck Year
1984
Truck Model
C20
Engine Size
305
I'm no emissions expert here, but will cats have a shorter life if the A/F ratio is overly rich due to not having feedback from an O2 sensor? Then again, I don't think the auto manufacturers had any feedback when they started using cats back in the mid-1970s. The idea was to convert as much NOx and CO as possible to nitrogen, oxygen, carbon dioxide, and water.

***Edit: I just noticed the OP has EFI. But my question above is still a good one for a carburetor-equipped engine.

The short answer is yes, cats will have a short life the with a richer mixture, but there were plenty of carbed vehicles built without feedback systems including the one I drive, that have cat (s). A properly tuned carb will go a long way to mitigate that.

I am simply choosing by pipe size.
I haven't look much farther than that when I am browsing the selections.

Well ****! The Magnaflo rep tells me that the convertor must reach a minimum of 350 degrees to "light off".

So I guess I'm **** out of luck. I'll have to rely on tuning the efi to get it the best I can.

I can't tell you for sure that you'll get the cats to 350F everytime you drive it, but the reaction inside the cats does cause heat. In other words if you put a pair of cats in they will run hotter than the exhaust pipe temps you are reading right now. I can tell you on my truck with single exhaust, there is no way the pipe before the cat is 350F on most days, but I can tell you the cat is working. Most modern cars do have the primary cats on the manifold, but that is mainly so they warm up faster and start working quicker. I would put them on and not worry to much about temps, just get them as close to the front as you can. However changing to the short headers would be better.
 

Rickf

Full Access Member
Joined
Jul 29, 2017
Posts
463
Reaction score
546
Location
Grafton NH
First Name
Rick
Truck Year
1974, 1954 & a 1937
Truck Model
K20
Engine Size
350
Would ceramic coated or wrapped headers push the heat towards the long tube collectors?

:cheers:
 

CorvairGeek

Full Access Member
Joined
May 7, 2012
Posts
548
Reaction score
908
Location
Boise
First Name
Jerry
Truck Year
1978
Truck Model
C20 Scottsdale
Engine Size
292 L6, T400
While none of them like a rich mixture, the 3 way catalyst (containing platinum, palladium, and rhodium) for control of HC / CO / NOx is dependent on a feedback fuel system (O2 sensor) for most efficient operation. The older design (2 way) for only HC and CO, not so much.

Did you know it is technically illegal (federal) to add a catalyst to a vehicle that didn't have one new, or add a second for true dual exhaust? You can thank the wizards of smart for the same reason that a used converter (which may be perfectly fine, lots of newer vehicles get totaled) cannot be legally resold. It can't be 'certified' that it is compliant.
 

metal tech

Full Access Member
Joined
Feb 6, 2014
Posts
63
Reaction score
17
Location
Choctaw OK
First Name
Al
Truck Year
84 & 85
Truck Model
K10 x2
Engine Size
305 x2
YES, long tube headers are going to need either ceramic coating or wrapped to keep heat in to light cat. This is also why most have to use a heated O2 sensor with headers, lack of heat. If you have the space put the cats right after the collector adapter. Trying to be green isn't easy on old stuff.
 

Latest posts

Forum statistics

Threads
41,852
Posts
903,534
Members
33,365
Latest member
rossivey
Top