Time for a new radiator

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Hatchet54

Full Access Member
Joined
Oct 23, 2018
Posts
276
Reaction score
248
Location
Wyoming
First Name
Red
Truck Year
1977
Truck Model
1500 Sierra Grande
Engine Size
350
I wish we could cut off the debate about plastic tanks, since most new aluminum radiators sold for the squarebody are like the one pictured in post #36 - note that there are no plastic parts in that radiator! This is not a Honda or Toyota.

I used the Champion 3 row for my '75 truck and the brackets and hoses all fit the same as stock. IIRC, the upper hose fitting is stepped so it can handle 2 different sizes of hose - a little odd, but it sealed well.

I am using a high flow 195 degree thermostat (which appears to be a little off in calibration), and it lets the engine get up to a little over 190, then opens and the temp moves down to 185. It stays at that temp regardless of driving conditions. Its been about 90 degrees outside lately, and I could let the truck idle with the A/C on, run at 60 mph traffic, etc., and its always at 185. The temp is measured with a Stewart Warner mechanical guage, tapped into the cylinder head sensor port.

Bruce

Did you use your stock fan for this setup?

Currently debating if the electric fan shroud combo is worth it. It's a lot of extra $$$...
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,904
Reaction score
7,249
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
Just finished my Cu730 big block Rad and Flex a lite 295 fan install give me 6 months and I will let you know how well it cools.

You must be registered for see images attach


You must be registered for see images attach
what's the part number on your upper radiator hose?
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,017
Reaction score
1,808
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
In response to Hatchet54 - I used the stock fan and shroud with the Champion 3 row radiator. I was already using a Hayden HD fan clutch, and I also have a Stewart Stage One high flow water pump and high flow thermostat.

Bruce
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,904
Reaction score
7,249
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
Upper Ac delco 26064X
Lower Ac delco 24205L

Have to trim the upper a little bit to get clean bends but otherwise fits perfect

You must be registered for see images attach
I’m wondering if that could replace my chrome atrocity. Nothing I’ve tried will clear my compressor.
You must be registered for see images attach
 

87_stepper

Junior Member
Joined
Jul 7, 2019
Posts
18
Reaction score
21
Location
Alberta Canada
First Name
Ryan
Truck Year
1987
Truck Model
V10
Engine Size
ZZ430
I’m wondering if that could replace my chrome atrocity. Nothing I’ve tried will clear my compressor.
You must be registered for see images attach

I am in the garage today I can send measurements if you put a level across the rad support and take a measurement to the ac compressor I will do the same.
 

Frankenchevy

Proverbs 16:18
Joined
Jan 3, 2018
Posts
5,904
Reaction score
7,249
Location
USA
First Name
Jeremy
Truck Year
Square
Truck Model
CUCV
Engine Size
Small
I am in the garage today I can send measurements if you put a level across the rad support and take a measurement to the ac compressor I will do the same.
Will do
 

Nonstop

Full Access Member
Joined
Nov 16, 2014
Posts
775
Reaction score
2,417
Location
Ca
First Name
Nick
Truck Year
1985
Truck Model
K2500
Engine Size
454
I’m wondering if that could replace my chrome atrocity. Nothing I’ve tried will clear my compressor.
You must be registered for see images attach

You might want to try one out of a 1990 v3500 with a big block. You need a new water neck as well. It comes straight up out of the block, runs pretty much straight forward toward the radiator, then runs along radiator to the inlet neck.
 

Hatchet54

Full Access Member
Joined
Oct 23, 2018
Posts
276
Reaction score
248
Location
Wyoming
First Name
Red
Truck Year
1977
Truck Model
1500 Sierra Grande
Engine Size
350
Just wanted to update this thread. After weighing my options I decided to go with a 3-row Champion. Ended up finding one for a pretty heavy discount on eBay so I went for it.

It was more or less a perfect swap for my OEM radiator and I got it lined up using the stock rubber mounts and shroud. Pretty clever the way they make everything fit the way they do.

It is worth mentioning for anyone looking to do a similar swap as I did...they don't give you any way to plug the trans cooler lines, so be prepared to make a run to the hardware store before you can fire up your truck. I got some stout aluminum bolts that were a perfect fit (sorry I forgot the thread count) and put some plumbing tape on the threads. That was weeks ago and no leaks.

I'm running a new Stant 185 thermostat, all stock fans, clutch, shroud, etc. and I sit on the first quarter mark on my temp gauge with this rad. Epic!

Thanks for all the discussion in this thread.
 

1985c20

Full Access Member
Joined
Jan 21, 2019
Posts
143
Reaction score
187
Location
Torrington, CT
First Name
Chuck
Truck Year
1985
Truck Model
C20
Engine Size
350
Usually the trans coolers will have plastic plugs in them but you don’t need anything. If you aren’t using it you can just leave them open to the air. There won’t be coolant coming out of them.
 

Kim Burke

Full Access Member
Joined
Dec 9, 2017
Posts
646
Reaction score
832
Location
Northern IN
First Name
Kim
Truck Year
1979
Truck Model
C1500
Engine Size
454
I haven't hooked up my temperature gauge yet, so it can't overheat. One less gauge to look at.

Hahaha hahaha! I finally quit watching mine running off the road after the 2500 mile trip.
 

MikeB

Full Access Member
Joined
Apr 4, 2014
Posts
1,745
Reaction score
935
Location
Justin, TX
First Name
Mike
Truck Year
1969
Truck Model
C10
Engine Size
355
Just had to jump back in here after I read an article in Car & Driver where they mentioned the efficiency of aluminum radiators allowing car hoods to be lower and air intakes to be smaller. The aluminum-haters here would freak out of they saw the size of the radiators in my Mustang GT and my wife's Infiniti -- both with (OMG!) nylon tanks.

Hey, I'm an old skool guy, but over the years I've had to replace WAAAAY too many brass & copper radiators or have them "boiled and rodded", so I don't want to get anywhere near another one.:eek:
 
Last edited:

MikeB

Full Access Member
Joined
Apr 4, 2014
Posts
1,745
Reaction score
935
Location
Justin, TX
First Name
Mike
Truck Year
1969
Truck Model
C10
Engine Size
355
Just finished my Cu730 big block Rad and Flex a lite 295 fan install give me 6 months and I will let you know how well it cools.

You must be registered for see images attach


You must be registered for see images attach
Beautiful engine bay you have there. :)
 

Forum statistics

Threads
41,850
Posts
903,452
Members
33,362
Latest member
Dhatch84
Top