Brakes

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Omar

Junior Member
Joined
Jun 15, 2019
Posts
4
Reaction score
0
Location
Texas
First Name
Omar
Truck Year
1981
Truck Model
C10
Engine Size
350
Hello folks...
I just bought a 1981 c10 needs some work, so it's a work In progress. My question is the rear brakes were bad so I went ahead and replaced pads drums,springs and cylinders. Once I had everything installed and started to bleed them using the buddy system. My buddy would pump the the brakes and hold but when I opened the bleeder valve I got nothing??? This went on for several attempts when I finally just had him mash the pedal, and at that point I got fluid. Once i was done we put the wheels back on and did a road test all was fine when i decided to mash my brakes as if it was an emergency, the truck stopped but when I released the pedal my rear brakes stayed locked up? I made it back home but my rear brakes were just a little hot...so my question is what should my next move be to check? Could it be my combination valve sticking? Any help would be appreciated...
 

78C10BigTen

Full Access Member
Joined
Apr 12, 2017
Posts
15,476
Reaction score
23,686
Location
pennsylvannia
First Name
Ted
Truck Year
1978
Truck Model
C10 BIG TEN
Engine Size
350
My first thought is a bad proportioning valve but im not good with brakes so... im sure more experienced people can help here. Be patient....
 

78C10BigTen

Full Access Member
Joined
Apr 12, 2017
Posts
15,476
Reaction score
23,686
Location
pennsylvannia
First Name
Ted
Truck Year
1978
Truck Model
C10 BIG TEN
Engine Size
350
Also just a thought that has nothing to do with the fluid but check to make sure your E brake hasnt been engaged in anyway somehow. Starting simple...
 

Old77

Administrator
Staff member
Admin
Joined
Aug 19, 2010
Posts
28,220
Reaction score
8,590
Location
Kansas City, Mo
First Name
Jacob
Truck Year
1977/1990/1991
Truck Model
C10 longbed/R1500 Burb/R3500 Dually
Engine Size
350/350/454
Not sure why this was posted in the Introduction section but I’ve moved it to the proper area for you
 

Omar

Junior Member
Joined
Jun 15, 2019
Posts
4
Reaction score
0
Location
Texas
First Name
Omar
Truck Year
1981
Truck Model
C10
Engine Size
350
Thank you...
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,018
Reaction score
1,810
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
IIRC, you have to manually flip the switch on the proportioning valve when you are bleeding the brakes, so that it provides equal pressure to both front and back systems. The valve should be located on the front driver's side of the truck, up under the left side frame rail or radiator support. You can follow the brake lines down to it.

In failure mode the proportioning valve is designed to switch internally and shift pressure to whichever brake system is still good, so it sends all pressure to the brakes that still hold. This means it may not pressurize the brake you are bleeding (since the valve is open) and you will have trouble getting it to bleed properly.

Bruce
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
28,956
Reaction score
23,468
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
I've never had to mess with the prop valve on these trucks when bleeding the brakes. While it may be the technically correct way, it's never been an issue.

Is it for sure both rear brakes hanging up? It could be the rear brake hose is collapsed internally and retaining pressure in the wheel cylinders.
 

RoryH19

Full Access Member
Joined
Aug 21, 2015
Posts
1,668
Reaction score
1,081
Location
Texas
First Name
Rory
Truck Year
1987
Truck Model
R10 Silverado SWB
Engine Size
350 TBI
Unless the prop valve is bad, there is no need to reset the slider to the middle.
I've had to replace one on my K5 as it had been sitting for many years.
Also are you getting a brake light on your dash even if the e-brake is off?
There is a sensor on the prop valve that will trigger the light in the dash if it has gone bad. Also if fluid is only going to front or rear.
 

4WDKC

Full Access Member
Joined
Jan 27, 2016
Posts
2,366
Reaction score
1,090
Location
Southern Florida
First Name
Kacy
Truck Year
1987
Truck Model
V10
Engine Size
350
sounds like the flexible line to the rear brakes collapsed and is restricting fluid from returning to the master cylinder. Lift the truck loosen the lines from each wheel to the flexible line on the rear axle then close it. Should be enough pressure release to turn the rear wheels. Replacement lines are inexpensive.
 

HotRodPC

Administrator
Staff member
Admin
Joined
Aug 29, 2010
Posts
47,008
Reaction score
8,976
Location
OKC, OK
First Name
HotRod
Truck Year
85 K20 LWB
Truck Model
Silverado
Engine Size
454 - Turbo 400 - 3.73
My vote is also for a collapser rubber hose just before the T over the axle pumpkin. Can't cost that much and it's time to replace it anyway so it's not a waste to give it a try.
 

RoryH19

Full Access Member
Joined
Aug 21, 2015
Posts
1,668
Reaction score
1,081
Location
Texas
First Name
Rory
Truck Year
1987
Truck Model
R10 Silverado SWB
Engine Size
350 TBI
Right it's $10 - 15 at most local part stores.
 

Charlie

Mopar by Birth. Chevy by Choice.
Joined
Aug 2, 2017
Posts
1,837
Reaction score
909
Location
Euless, Texas
First Name
Don
Truck Year
1974
Truck Model
Cheyenne 10 LWB
Engine Size
350/TH350/AC/4 BBL Quadrajet
:welcome:
 

Latest posts

Forum statistics

Threads
41,854
Posts
903,556
Members
33,367
Latest member
texdave
Top