Motor Dies While Driving

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

cfitz95

Junior Member
Joined
Jun 15, 2015
Posts
10
Reaction score
2
Location
Northern Virginia
First Name
Conor
Truck Year
1986
Truck Model
k10
Engine Size
350
My 86 K10 has a 350 with HEI. I was driving for about 30 minutes and then the motor died while cruising around 40mph. I pull off to the shoulder, throw it in park, and it fires right back up immediately and idles perfect. I drive maybe another 100 feet and it dies again. Same thing - throw it in park, start the motor up, drive about 100 feet and it dies. Did this many times, sometimes the motor was harder to start, but most of the time would start up no problem. It idles perfectly fine and only dies while driving/accelerating. It has good vacuum at idle, it has fuel, and battery is showing 14.6V at idle. I'm almost positive it is an ignition issue because when it dies, it doesn't stumble or cough like it is out of fuel. It cuts out and dies immediately like the key was turned off (sometimes backfires out the exhaust after it dies). I tested resistance on the coil and it checks out fine. All the plug wires are good and not arcing or cracked. Would this point to the ignition module or pickup coil? Any help is appreciated!
 

chengny

Full Access Member
Joined
Feb 22, 2012
Posts
4,086
Reaction score
1,008
Location
NH
First Name
Jerry
Truck Year
1986
Truck Model
K3500
Engine Size
350/5.7
My 86 K10 has a 350 with HEI. I was driving for about 30 minutes and then the motor died while cruising around 40mph. I pull off to the shoulder, throw it in park, and it fires right back up immediately and idles perfect. I drive maybe another 100 feet and it dies again. Same thing - throw it in park, start the motor up, drive about 100 feet and it dies. Did this many times, sometimes the motor was harder to start, but most of the time would start up no problem. It idles perfectly fine and only dies while driving/accelerating. It has good vacuum at idle, it has fuel, and battery is showing 14.6V at idle. I'm almost positive it is an ignition issue because when it dies, it doesn't stumble or cough like it is out of fuel. It cuts out and dies immediately like the key was turned off (sometimes backfires out the exhaust after it dies). I tested resistance on the coil and it checks out fine. All the plug wires are good and not arcing or cracked. Would this point to the ignition module or pickup coil? Any help is appreciated!


I would have to agree - that it is an electrical problem associated with the ignition system. But in my (limited) experience, electronic components don't keep coming back to life. Try this easy diagnostic:

It will tell you whether the distributor has an internal problem - or the issue is loss of power to the coil primary side. Just run a temporary external jumper to the BAT terminal on the cap. Where the power comes from is not important - as long as it is independent of the ignition switch and the interconnected wiring. Just run it to the firewall junction block for example. If the problem goes away...you're dropping power to the coil primary. If it persists... there may be a problem within the distributor itself (e.g. the ICM or pickup coil). This test might not specifically identify the problem but may help save you some time & $$.
 

cfitz95

Junior Member
Joined
Jun 15, 2015
Posts
10
Reaction score
2
Location
Northern Virginia
First Name
Conor
Truck Year
1986
Truck Model
k10
Engine Size
350
Interesting, I’ll definitely give that test a try tomorrow. I’ll report back my findings. Thanks!
 

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,018
Reaction score
1,809
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
I've also heard of a few folks having problems with an HEI cutting out from the movement of the vacuum advance mechanism. I'm not sure if it hits wires, shorts out, or whatever.

The easiest test for the advance would be to disconnect the advance can, run the engine up to cruising RPM so the mechanical advance has started to move, and then pull vacuum on the advance so that it moves the mechanism back and forth.

It might also be a fuel problem, since at cruise you are pulling a lot more fuel from the bowl than at idle. If there is a piece of rubber hose or other junk partially blocking the flow, you might suck the bowl dry quickly at higher RPM, but stlll have enough flow to let it idle normally after a restart. You could test for this problem by just running it at about 2000-2500 RPM for a few minutes while parked to see if it seems to run out of fuel. It will be noisy, but won't hurt anything. I've run it at 2500 RPM like that for quite a while during cam break-in.

Bruce
 

mgarland

Junior Member
Joined
Jan 1, 2019
Posts
22
Reaction score
5
Location
West of Indy
First Name
Mark
Truck Year
1985, 1989
Truck Model
K30X2
Engine Size
Big
Sounds like an ignition problem to me, I've had a couple Of hei's do this to me, they would be fine until they would get heat soaked after running for a while. Since you already checked the coil and it ohmed out correctly then I would put a pick up coil and module in it. If you have an old hei laying around just swap it out and see if that makes a difference.
Mark
 

mags468

Junior Member
Joined
Jan 15, 2017
Posts
18
Reaction score
2
Location
Bradford,Pa
First Name
Nick
Truck Year
1990
Truck Model
Suburban
Engine Size
350
Fuelpump relay. I went through alot before I found mine was bad.
 

WHEELMAN

Full Access Member
Joined
Aug 9, 2011
Posts
136
Reaction score
11
Location
HICKORY TAVERN SC
First Name
BILL
Truck Year
1986
Truck Model
C10
Engine Size
454 v8
Most times ignition module.i doubt it would keep cranking up.if it was the fuel pump.a manual pump.

Don't forget to use the grease under the module.
 

buildin64

Junior Member
Joined
May 14, 2017
Posts
11
Reaction score
5
Location
Michigan
First Name
Garry
Truck Year
1975
Truck Model
K5
Engine Size
350
I had the same thing going on. I finally figured out that I didn't need to pull over to the side of the road. Just take your foot off the throttle, put the trans into neutral, turn the key off quickly and restart. Don't pump the throttle or it will most likely backfire when it restarts as there will be raw fuel in the bowl.
When I had the time I changed out both the ignition switch at the bottom of the steering column that is an electrical connection that is actuated by the key cylinder and the ignition module that sits on top of the distributor. As someone earlier mentioned make sure to use the electrical grease. You may want to also change out the distribution cap itself.
I did all of this at the same time since I bought the truck used and didn't have a clue as to the last time any of it had been touched. This cured my problem. Hope it works for you.
 

peats

Full Access Member
Joined
Dec 2, 2016
Posts
288
Reaction score
236
Location
Pennsylvania
First Name
john
Truck Year
72k5, 81c10 short step, 83k10 short fleet, 03 SSR. 25 chevy doodlebug
Truck Model
k5 c10 k10 SSR doodlebug
Engine Size
406 360 6.2 5.3 171
i couldn't believe this post when i read it because my fresh frame on resto on my '81 c 10 360/th350 is doing the exact thing!it feels like it is running out of gas and will limp along at just off idle but will not take throttle. any input is welcome. sorry to barge in on this post but i could use some imput.
 

Wumbo

Full Access Member
Joined
Dec 12, 2018
Posts
1,006
Reaction score
3,781
Location
Illinois
First Name
Rob
Truck Year
1986
Truck Model
C20
Engine Size
454
i couldn't believe this post when i read it because my fresh frame on resto on my '81 c 10 360/th350 is doing the exact thing!it feels like it is running out of gas and will limp along at just off idle but will not take throttle. any input is welcome. sorry to barge in on this post but i could use some imput.

If it will idle, but bogs when you try to accelerate, it's probably fuel related.

Start with a new fuel filter.
 

peats

Full Access Member
Joined
Dec 2, 2016
Posts
288
Reaction score
236
Location
Pennsylvania
First Name
john
Truck Year
72k5, 81c10 short step, 83k10 short fleet, 03 SSR. 25 chevy doodlebug
Truck Model
k5 c10 k10 SSR doodlebug
Engine Size
406 360 6.2 5.3 171
everything is new including the gas tank,fuel pump and carb.
 

Wumbo

Full Access Member
Joined
Dec 12, 2018
Posts
1,006
Reaction score
3,781
Location
Illinois
First Name
Rob
Truck Year
1986
Truck Model
C20
Engine Size
454
everything is new including the gas tank,fuel pump and carb.

How many miles since the carb was installed?

Last week I had the same problem. Good idle, but stumbling off idle. Hard to accelerate. New fuel filter with about 600 miles on it. This is a quadrajet with the filter on the inlet of the carb.

Pulled the fuel filter. Outside looked fine. Cut it open to find fine black particulate, which I can only assume to be fuel line deterioration. Replaced the fuel filter and it ran fine. Then I went ahead and replaced all the rubber fuel lines, tanks, and selector valve.

This truck had sat for several years, and that could have contributed to the fuel lines condition.

For $2.00 though, I would change the filter and see if it fixes it.
 

peats

Full Access Member
Joined
Dec 2, 2016
Posts
288
Reaction score
236
Location
Pennsylvania
First Name
john
Truck Year
72k5, 81c10 short step, 83k10 short fleet, 03 SSR. 25 chevy doodlebug
Truck Model
k5 c10 k10 SSR doodlebug
Engine Size
406 360 6.2 5.3 171
mine is a new build with only 30 miles on it but checking the fuel filter is a good place to start. i use the stone filters
 

73c20jim

Full Access Member
Joined
Jun 11, 2018
Posts
2,282
Reaction score
2,924
Location
Tombstone, AZ
First Name
Jim
Truck Year
1973, 1973
Truck Model
C20 2WD Custom Deluxe. C10 2WD Base Model
Engine Size
350 CID 195/260 HP Goodwrench crate, 400 CID 2bbl
Bad ground somewhere???

:patriot::patriot:
 

Forum statistics

Threads
41,851
Posts
903,510
Members
33,365
Latest member
rossivey
Top