Replace A/C entirely

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

WillSquared

Full Access Member
Joined
Mar 19, 2014
Posts
155
Reaction score
27
Location
Arkansas
First Name
Will
Truck Year
1986
Truck Model
C10
Engine Size
350
So I have had nothing but trouble out of my AC system since I bought my truck a few years ago. I’ve been through a couple compressors, and now the heater core is leaking. I’d like to just take all the old out and replace it all with new parts. Could someone who knows more than me list out what all I’d need to do that? Here’s a list of what I think. Let me know if I do or don’t need it all. Thanks

Compressor
Accumulator
ORing set
Orifice tube
Core/Cap set
Suction/Discharge lines
Heater core
Condenser
Blower motor
Blower motor control module


Sent from my iPhone using Tapatalk
 

yevgenievich

Full Access Member
Joined
Mar 1, 2014
Posts
4,781
Reaction score
3,298
Location
Texas
First Name
Viktor
Truck Year
sad
Truck Model
very sad
Engine Size
less sad
Jumping over to a sanden style compressor might help with compressor reliability.
 

Snoots

Full Access Member
Joined
Jan 23, 2013
Posts
8,158
Reaction score
15,957
Location
Georgia
First Name
Roger
Truck Year
1973
Truck Model
Jimmy Sierra
Engine Size
350
Sanden 508
 

WillSquared

Full Access Member
Joined
Mar 19, 2014
Posts
155
Reaction score
27
Location
Arkansas
First Name
Will
Truck Year
1986
Truck Model
C10
Engine Size
350
Mine is the pancake style compressor. What would have to be changed to go to the Sanden?


Sent from my iPhone using Tapatalk
 

yevgenievich

Full Access Member
Joined
Mar 1, 2014
Posts
4,781
Reaction score
3,298
Location
Texas
First Name
Viktor
Truck Year
sad
Truck Model
very sad
Engine Size
less sad
Depending if v belt or serpentine. Worst case brackets and hoses. Best case brackets and adapter. And the usual dryer/orifice/flush/seals for opening up the system
Mine is the pancake style compressor. What would have to be changed to go to the Sanden?


Sent from my iPhone using Tapatalk
 
Last edited:

75gmck25

Full Access Member
Joined
Oct 13, 2016
Posts
2,018
Reaction score
1,809
Location
Northern Virginia
First Name
Bruce
Truck Year
1975
Truck Model
K25 Camper Special TH350 NP203
Engine Size
5.7
I've replaced almost all the A/C components in my truck, so I can give you an idea of how it would work.

- Blower motor and heater core were replaced with OEM components.
- OEM steel fan with severe duty fan clutch
- Evaporator is still original OEM, along with low temp probe and cutoff switch that is inserted into it. Evaporator was flushed to remove all old oil.

- Replaced condenser with largest parallel flow that would fit. After the fact I found out that the large OEM condenser may have been fine, but opinions vary.
- Replaced A6 compressor with a Sanden compressor and brackets from Vintage Air. Had to figure out the best belt length, but otherwise a straightforword job with my V-belt system.
- Replaced filter/drier with one from about an '85 truck, mostly because the top fittings lined up better. OEM could have been made to work, but the hose fitting was on the bottom.
- Added a high pressure cutoff switch, screwed into old R12 port fiting. Probably not needed, but recommended. You can just wire it inline with the original low pressure cutoff.
- Switched to Ford blue orifice. Supposed to work better than GM white with R134a.

- Had custom barrier hoses made up to connect from compressor to condenser and compressor to evaporator. They put the new R134a charge ports in the fittings where they connect to the compressor. Very easy to reach when charging.
- The lower evaporator fitting on a '75 is large diameter and it is where the orifice tube fits. They had to make a custom fitting (brazed two together) for that connection because its a small diameter hose but a large fitting. I think the orifice is in a different location on newer trucks.
- Reassembled with all new green O-rings, lightly lubed with PAG oil
- Recharged with about 7-8 oz of PAG oil and an R134a charge that is about 75% of the R12 charge. Used the gauges to tune the charge a little further, based on pressures.

This setup worked well for a couple of years, and then I had problems chasing down a leak. Leak turned out to be the body of the high pressure switch leaking - not what I expected, but I guess its a cheap switch. Currently running again and able to drop the temps down very quickly.

Bruce
 
Last edited:

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
3,658
Reaction score
6,596
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
Do you plan on keeping this truck? If the answer is yes, then shitcan the OE system, bite the bullet and buy the Vintage Air Surefit system. I just did this on my 85. You will lose 20 miles of useless vacumn hoses/diaphrams, wires, relays, and stiff cables. It's plug and play, modern technology, reliable and effective. This comes at a price ($1200 ish). Buy once- cry once. I live in Yuma, Az. Summer days are 110+. I get 45 degrees out of the vents. Worth every penny.
 

yevgenievich

Full Access Member
Joined
Mar 1, 2014
Posts
4,781
Reaction score
3,298
Location
Texas
First Name
Viktor
Truck Year
sad
Truck Model
very sad
Engine Size
less sad
Some temperatures can be archieved with a stock system using sanden compressor as well. All depends on current condition and budget.

Do you plan on keeping this truck? If the answer is yes, then shitcan the OE system, bite the bullet and buy the Vintage Air Surefit system. I just did this on my 85. You will lose 20 miles of useless vacumn hoses/diaphrams, wires, relays, and stiff cables. It's plug and play, modern technology, reliable and effective. This comes at a price ($1200 ish). Buy once- cry once. I live in Yuma, Az. Summer days are 110+. I get 45 degrees out of the vents. Worth every penny.
 

roundhouse

Full Access Member
Joined
Apr 5, 2014
Posts
669
Reaction score
527
Location
atlanta ga
First Name
justin
Truck Year
77,78,79,80 ?
Truck Model
K10
Engine Size
350
I used the vintage air also
And it’s an easy install

Kinda pricy but also thenother OEM parts add up
And the vintage air is all new parts
 

WillSquared

Full Access Member
Joined
Mar 19, 2014
Posts
155
Reaction score
27
Location
Arkansas
First Name
Will
Truck Year
1986
Truck Model
C10
Engine Size
350
Thanks for the info guys. I am torn. I’ve considered the Vintage Air but I could replace the stock setup 3 times over for the price of the vintage air kit. I’ll just have to weigh my options.


Sent from my iPhone using Tapatalk
 

Battlac40

Full Access Member
Joined
May 27, 2017
Posts
191
Reaction score
97
Location
New Mexico
First Name
James
Truck Year
1981
Truck Model
K1500 Sierra Classic
Engine Size
350
Pictures are nice !
.... ?
 

Latest posts

Forum statistics

Threads
41,852
Posts
903,531
Members
33,365
Latest member
rossivey
Top