D60 axle shaft seal woes!

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

heavyleft

Full Access Member
Joined
Jan 2, 2012
Posts
396
Reaction score
29
Location
Fayetteville, NC
First Name
Mike
Truck Year
1987
Truck Model
V10/K5
Engine Size
350ci
Passenger side axle shaft seal sprung a leak today (D60). Looks like I get to spend Saturday tearing my axle apart. Anyone have any good advice to make this easier? Experience do's and dont's?

Thanks in advance.
 

crazy4offroad

Equal Opportunity Destroyer
Joined
Jul 30, 2010
Posts
8,468
Reaction score
1,070
Location
West BY-GOD Virginia
First Name
Curt
Truck Year
1979
Truck Model
K-10
Engine Size
350/SM465/NP205
You talkin about an inner seal? Damn man I think it would have to be leaking pretty bad for me to dig that far to fix it. Keep your carrier bearing shims grouped for the corresponding sides they go in, but I don't think I need to tell ya that. I used a piece of 4' long re-bar with an angle cut on the end to knock the seals out with. When re-installing the axleshafts examine the surfaces the seals rides on and clean them up if they need it, may even need sleeved or built up/turned down if you know someone with a lathe, and good with it.
 

heavyleft

Full Access Member
Joined
Jan 2, 2012
Posts
396
Reaction score
29
Location
Fayetteville, NC
First Name
Mike
Truck Year
1987
Truck Model
V10/K5
Engine Size
350ci
Thanks, was hoping you would chime in....lol.
 

smurph20

Full Access Member
Joined
Jul 13, 2011
Posts
2,063
Reaction score
23
Location
Clyde, Arkansas 72717
First Name
Brad
Truck Year
1986
Truck Model
K20
Engine Size
350/SM465/NP208/4.10's
Or better yet just send it to me and ill be happy to take your problem axle off your hands lol.
 

crazy4offroad

Equal Opportunity Destroyer
Joined
Jul 30, 2010
Posts
8,468
Reaction score
1,070
Location
West BY-GOD Virginia
First Name
Curt
Truck Year
1979
Truck Model
K-10
Engine Size
350/SM465/NP205
Didn't you put chromoly axleshafts in recently? I know you did outers but not sure about inners. If you did replace the inners did you mic them against your old ones? Were the seals original, or old-ish/used/abused?
 

heavyleft

Full Access Member
Joined
Jan 2, 2012
Posts
396
Reaction score
29
Location
Fayetteville, NC
First Name
Mike
Truck Year
1987
Truck Model
V10/K5
Engine Size
350ci

crazy4offroad

Equal Opportunity Destroyer
Joined
Jul 30, 2010
Posts
8,468
Reaction score
1,070
Location
West BY-GOD Virginia
First Name
Curt
Truck Year
1979
Truck Model
K-10
Engine Size
350/SM465/NP205
Those are neat, reminds me of the old grease wick outer seals. Basically they were just a cotton rope soaked in grease you would pack in around the outer end of the axle tube. Good for keeping the muck out. Be aware the inner axleshafts have some wobble to them in 4WD so they may not have a long life doing much trail riding/rock crawling. They may help stabilize the wobble though but I'm sure it could result in shorter life.
 

Forum statistics

Threads
42,174
Posts
910,700
Members
33,670
Latest member
ajiuo666
Top