Hi, looking for an original door pocket for my 78 k10.
I'm missing the passenger side. Interior is buckskin.
No problem if faded, I'll redye as I did with the one in the picture.
Thanks
The support bar in my 78 k10 is missing.
It has the large bolts still in the t-case so I assume it had one.
Has the original TH350 and np203. Does anyone have one?
Also would one from a 81+ with a np208 be the same rod?
Thanks
Hello,
Looked through the threads but couldn't find any details.
Need to install the fuel tank selector valve in my 78.
PO removed the unit and connected the left tank directly to the lines on the frame rail.
I found this thread which is probably what it looked like...
I noticed my 78 k10 has the bracket on the right rear outside frame rail for the glide out carrier.
Unfortunately that's the only part still on the truck.
Does anyone have one?
Couple of pics I've found.
Hello.
I've been researching axle swaps for my k5. I have a 14bSF from a 4x4 gmt400. It will widen the rear axle to basically the same width as the stock front axle.
I was also thinking of converting to disk at the same time since the drums are shot.
I then thought about using the gmt800 with...
Hello,
Has anyone swapped the front 7/16 wheel studs to 9/16 or 14mm?
The 14B SF rear axle I have for my k5 came with 14mm and would like them to match when I install.
Any part numbers for the studs?
Will I need to drill the rotors?
Thanks.
Hello,
Has anyone changed from 15" wheels to 17" and noticed a difference in ride?
Is the ride better or worse, more stable, etc?
Will be for my 4x4 K5 with 33x12.5 tires.
Thanks.
What modern GM mirrors are being used to upgrade a square?
No need for Onstar or backup camera.
Would like compass, temp and autodim. I would go to a salvage yard and take the harness with the mirror.
Thanks.
I've had several squares from the 80's and everyone had a windshield antenna.
My 78 has a fender mounted one. I've also seen 88+ burbs and 3+3's with them too.
What years did they use each style and why?
Well this is what happens when your k5 has been gone for too long at paint and body.
78 k10 Silverado SWB
350/TH350/np203 dana 44 and 12 bolt rear.
Looks to have it's original buckskin interior too.
Will need metal work like my k5 did.
Let's just say it will be a project.
Hello all.
Looking for the radiator cover/mounts for a 454 or diesel rad.
Need one to span the gap from my core support to rad on my LS swap.
I think one of these might work.
Thanks.
Do any of the step sides from the 70's have body trim?
Specifically the aluminum that runs along the body that a fleet side has?
Saw a 79 Silverado that only had the trim around the cab window. Didn't see any side trim or holes where it may have been.
Thanks.
Hi,
Are there any k30's for sale around?
Just a driver or one that can use some work.
Don't need a show truck.
A Silverado with 454 and TH400 would be great.
Thanks,
Rory
Has anyone installed a hydroboost from a 2003, 4, 5... suburban, Tahoe, escalade... into a square?
If so, assuming I would have to use the pedal, hydroboost unit and master cylinder.
Power steeping pump would also need the extra connector.
Thanks.
Plan to add a steering gear support to my k5.
Have seen the ORD bolt on here:
https://www.offroaddesign.com/bolt-in-steering-box-brace-for-81-91-gm-4wd-trucks.html
And the ORD weld on:
https://www.offroaddesign.com/weld-on-frame-repair-kit-for-73-91-gm-trucks.html
Pros and Cons from any...
Hello,
What year did the fuse block change from round tube to the blade style?
Assuming somewhere between 79 - 81.
Any issues in retrofitting the later blade style into the older trucks?
I would change the harness inside the cab and under the hood.
Thanks