Search results

  1. 8

    Did i just fry my 700r4?

    I dont have reverse either. The thing just quit moving all together
  2. 8

    Did i just fry my 700r4?

    I will hook it up and see what happens thanks guys
  3. 8

    Did i just fry my 700r4?

    Would i be able to pull it out and zip tie it in the fully extended position to get full pressures? Truck isnt going to be on the road for a few years anyway juat need it to move around the property
  4. 8

    Did i just fry my 700r4?

    Long story short i just put a winters aluminum intake and holley 4150 in my c20. My TV cable was too short to let the throttle go to wide open, and since the truck isnt on the road i figured itd be okay to disconnect it as long as i wasnt going on the road with it. I must have been wrong because...
  5. 8

    Engine Identification?

    Okay thanks! When I looked it up it came up as 400 for some reason
  6. 8

    Engine Identification?

    Will check in the morning
  7. 8

    Engine Identification?

    So if it's a 400 it should have one of those two numbers behind the head?
  8. 8

    Engine Identification?

    So my 82 c20 has a small block. I was told it was a 350 but when I look up the number on the pad behind the alternator it says it's a 400. Code is V08 TTC... which is it??
  9. 8

    K20/k30 build Thread

    All said and done
  10. 8

    K20/k30 build Thread

  11. 8

    K20/k30 build Thread

    Tons of snow needed to be shoveled
  12. 8

    K20/k30 build Thread

    Finally got a hold of a good 4x4 one ton SRW frame, so it was time to dig out the c20 to start harvesting the body and preparing for a body swap. Took a lot of shoveling and getting it stuck, but I got er out! Sent from my iPod touch using Tapatalk
  13. 8

    84/82 K20 Build Thread

    Yea i was looking at it this morning and realised that literally every single bolt on the front end would need to be torched off and replaced and how much stuff needed to be done that i'd be way ahead by scrapping the idea
  14. 8

    84/82 K20 Build Thread

    Well, plans changed again, Came across this GMC 3/4 Ton 4X4 on kijiji tonight owned by a local body shop. Comes with a plow that i'd take off but it has a lift already installed and its actually in pretty good shape. Went and looked at it tonight but going back to look in the day time soon...
  15. 8

    84/82 K20 Build Thread

    That is what i originally wanted to do, but everyone else on here said not to because its a complete pain in the ass and not worth the effort
  16. 8

    84/82 K20 Build Thread

    Here's my new plan. I've noticed that the engine in this truck leaked so much oil that everything on the frame up front isnt even rusted at all. Still had original paint after I scraped the crud off it. I'm going to take the C20 frame and chop the front end off and weld the front end from the...
  17. 8

    84/82 K20 Build Thread

    Thanks guys! I'm actually not even working right now so I'm scraping my bank account dry right now lol but I have a job lined up at the local ford dealer (yea I know ford on a chevy forum lol) mounting and balancing tires so I should be able to start buying a lot more stuff for the truck than I...
  18. 8

    84/82 K20 Build Thread

    Diesel up here is usually about a dollar to a dollar and a half cheaper than gas
  19. 8

    84/82 K20 Build Thread

    How would a turbo 400 be mated to a 6bt 12 vavle?
  20. 8

    84/82 K20 Build Thread

    Shifting topics now, I have an opportunity to pick up a cheap 6bt cummins and was thinking of throwing it in this truck. Thinking it would be a good idea as i probobly wouldnt be able to afford to feed the 350 in it after everything ive done to it.
  21. 8

    84/82 K20 Build Thread

    I do have a sandblaster here but no sand and it would make a hell of a mess
  22. 8

    84/82 K20 Build Thread

    Thanks for the info Hot Rod, I'll look into that. Where do you normally buy something like that? I'll search for it later, i'm out hunting right now. Yea 89Suburban you can't beat working on a project :)
  23. 8

    84/82 K20 Build Thread

    Ended up with the top and sides of the C channel sanded. Got the frame up on stands with the wheels off as well. That pile of dirt by the broom? That's not dirt. Its rust that fell off the frame while beating on it with the chipper
  24. 8

    84/82 K20 Build Thread

    After chipping and Sanding
  25. 8

    84/82 K20 Build Thread

    Out tonight Chipping rust and sanding with flap wheels

Latest posts

Forum statistics

Threads
42,056
Posts
908,134
Members
33,538
Latest member
Chuchito
Top