Search results

  1. M

    Bad Combo?

    Did you ever get this sorted out?
  2. M

    What have you done to your square lately??

    Smoked some retard with a brandnew F150 right off the line. LMAO hahahaha. Brand new pickup truck and he couldn't even come close to keeping up haha
  3. M

    Relay vs vacuum switch

    The vacuum switch uses the engines vacuum to operate the TCC
  4. M

    Custom power station in ashtray

    Good Job !!! I like how you incorporated a switch so that the LED doesn't run down the battery :waytogo:
  5. M

    New GM Motors (Variable Valve Timing)

    I was looking for either a 4.3 V6 or 5.3 V8 $35K-40K to use as a family vehicle with short commute trips. But NOOOOO I now have to buy a $55K 3/4 ton truck with a 6.0 just so I can have a reliable vehicle that is worth spending money on! $40K on a piece of shit or $55K on a way over built...
  6. M

    New GM Motors (Variable Valve Timing)

    Apparently the 07-13 setup shut down the same 4 cylinders every time. The new version will cancel any of the 8 and not necessarily at the same time either. It is supposed to be a fully ECM controlled system that uses a large amount of variables to determine which and how many cylinders shut...
  7. M

    Running a 4" lift and 37s??

    Oh as far as the 37s go you will need to do some major trimming to stuff 37s under a 4" lift. You would need an 8" lift to properly clear 37s with out bent fenders.
  8. M

    New GM Motors (Variable Valve Timing)

    Well I found this article plus a few others about the VVT and it looks like a real good and simple performance upgrade to any LS engine! Should be quite reliable too :) http://www.hotrod.com/how-to/engine/hrdp-1007-gms-variable-valve-timing-system-performance-test/ The AFM on the 1/2 tons...
  9. M

    Door adjustment

    Yep move both door hinges at the body side of the hinge back how ever far you need.
  10. M

    Running a 4" lift and 37s??

    Ok that will work then.
  11. M

    Fix Slamming Doors - Striker Door Latch Repair

    Oh and the pin is installed before the truck is painted at the factory so its really easy to see where the pin should be when it comes time to reinstall it.
  12. M

    Fix Slamming Doors - Striker Door Latch Repair

    Both of my trucks have no tack welds on the nut. They are square pieces with little cleats on the surface to stop them from spinning. Every truck I have owned has been the same. Even if they were welded it would be easy to just use a large washer and a nut with a lock washer.
  13. M

    Fix Slamming Doors - Striker Door Latch Repair

    Ya as long as you have a regular cab pickup. Simply remove the corner speaker and then just reach around the door pillar to hold the nut while you use a T-45 socket to undo the striker pin/bolt. If you have a crew cab or jimmy it may be more complicated to gain access to that nut....but the...
  14. M

    Compatible rear end for 73

    I would check the back lash and maybe think about replacing the outer bearings. The Astro van is a mini van/truck. It will not fit unless you want the wheels to be well inside the wheel wells. You need a full size truck axle. Usually there is a lot of metal in the diff if its going out. So...
  15. M

    Dakota Digital switch/button placement?

    Just put the switches under the gauge bezel on the drivers side. Drill a hole or whatever closer to the steering column, on the metal part of the dash. You wont notice it much there and it wont get accidentally bumped, yet it is easy to reach there but you will have to intentionally do it rather...
  16. M

    14 bolt brakes

    ............ Ill measure it tomorrow for you
  17. M

    Problem with heat in the cab

    I dunno. I have bare floors and my heater core is functional all year round and I don't feel any heat at all in the summer or winter unless I turn on the heat. Why not open the fresh air ducts and see if that solves it? But I don't see why it should be that warm unless something is not plumped...
  18. M

    Running a 4" lift and 37s??

    What gear ratio are you running? And what transmission?
  19. M

    What have you done to your square lately??

    Installed 1/2" pex on my door striker pins last night :) The factory one has a larger ID then the door pin so its fairly loose and able to rotate on the pin. My OCD would not allow me to use the pex with a slit down the side lol The 1/2" pex ID is smaller than the pin. I removed the pin...
  20. M

    33"x10.50 before lift

    Some say yes. I have 285/75r16s on stock suspension and it fits good with just a little wiggle room. So unless your suspension is sagged it should fit ok. But Im not positive about that.
  21. M

    Fix Slamming Doors - Striker Door Latch Repair

    Ya that's a good point about it spinning around every time the door closes. The factory one has a larger ID then the door pin so its fairly loose and able to rotate on the pin. My OCD would not allow me to use the pex with a slit down the side lol I actually just did mine last night and the...
  22. M

    New GM Motors (Variable Valve Timing)

    Keith Seymore
  23. M

    New GM Motors (Variable Valve Timing)

    Anybody know anything about the new GM 1/2 ton VVT AFM engines? Are they reliable? Are they expensive or inexpensive to maintain or are they a nightmare waiting to happen? I cant seem to find any real info on these engines. Does anyone know where a guy could find out about these engines? And...
  24. M

    Bad Combo?

    Hmmmm Im not sure. Maybe chengny or circuitguy could help
  25. M

    already want a bigger cam

    Well I guess that's it then! :) Im looking forward to your 6.0 LSX swap thread :) :popcorn:

Latest posts

Forum statistics

Threads
42,065
Posts
908,289
Members
33,542
Latest member
willyg
Top