Search results

  1. bigcountryguy19

    Tran..

    Make shure you have a dual bolt pattern flex plate. Sent from my iPhone using Tapatalk
  2. bigcountryguy19

    K-15 Project from Good Ol' Montucky!

    Nice truck! Sent from my iPhone using Tapatalk
  3. bigcountryguy19

    under powered

    Is it smoking or anything? Maybe the engine is just tired and needs a rebuild? Sent from my iPhone using Tapatalk
  4. bigcountryguy19

    I need a name

    Thirsty? Lol Sent from my iPhone using Tapatalk
  5. bigcountryguy19

    Silicone on a rubber gasket?

    Are those gaskets that much better than the four piece? I have never used one. Sent from my iPhone using Tapatalk
  6. bigcountryguy19

    Priming fuel system?

    Would that really be an issue? Of it cranking for a while on a new cam? I just never thought that would really matter? I would just like to know. Sent from my iPhone using Tapatalk
  7. bigcountryguy19

    Silicone on a rubber gasket?

    You can use silicone if u want to, just snug the bolts till it dries then tighten them up all the way Sent from my iPhone using Tapatalk
  8. bigcountryguy19

    85-87 hydro pedals

    Can't y'all just kick this a hole out of here? Sent from my iPhone using Tapatalk
  9. bigcountryguy19

    Wiper issues

    Most likely the wiper motor gearbox. Sent from my iPhone using Tapatalk
  10. bigcountryguy19

    Choosing a new carb and intake

    I built a 355 with flat tops, 76cc heads and the edelbrock performer package. (Cam, lifters, valve springs, timing set, and intake with a 600 cfm Holley carb. I had 3:55 gears and 33 inch tires. It had impressive power. I ran stock exhaust manifolds too. I hate headers. Sent from my iPhone...
  11. bigcountryguy19

    Choosing a new carb and intake

    That tells u all you need to know, use that info when buying an intake and carb. Don't forget valve springs. Sent from my iPhone using Tapatalk
  12. bigcountryguy19

    Carb Bog

    I agree, well besides the quadrajet lol Sent from my iPhone using Tapatalk
  13. bigcountryguy19

    Choosing a new carb and intake

    I like edelbrock intakes myself, what rpm range is the 268 voodoo cam? You should always match your cam rpm to your intake rpm. Same with the carb, read what they are best intended for. I only build high torque low rpm engines, cause that's what I like in my 4x4's. I like edelbrocks performance...
  14. bigcountryguy19

    CL bonus

    I have never seen one with that trim panel. Sent from my iPhone using Tapatalk
  15. bigcountryguy19

    I suspect a rear main leak has developed

    I would replace the oil pump, for one it's not that expensive, for two do you really want to tear it all back apart again if it does take a dump? When I replaced my rear main I had to losen all the main caps and slightly drop the crank to get the upper seal in, it wouldn't rotate out. I highly...
  16. bigcountryguy19

    Question about splitting sm465 from transfer case

    You could try that, I personally don't do it that way but that doesn't mean it can't be done. It not hard dropping the shafts, and pullin t case out first. Sent from my iPhone using Tapatalk
  17. bigcountryguy19

    I suspect a rear main leak has developed

    I would say it's the rear main, or pan gasket. Could possibly be the rear intake gasket, maybe it slipped out. Sent from my iPhone using Tapatalk
  18. bigcountryguy19

    TH350 2wd to 4x4

    IMO, it would be best to find a whole 4x4 setup out of a donor truck, so you can get the proper driveshafts and cross members. Doesn't really matter what t case you get, as long is it matches your drive lines (one piece or two piece). A np205 is great, but a np208 works fine too. As hot rod said...
  19. bigcountryguy19

    Wobble wobble wobble, rear axle.

    Shocks are probably due lol. On the ball joints an tie rod ends, you are correct, just jack up the front of the truck and wiggle stuff looking for play in them, I use a small pry bar on the steering knuckle and just try to wiggle it around, if it doesn't move your good. Sent from my iPhone...
  20. bigcountryguy19

    Wobble wobble wobble, rear axle.

    Good point, I was merely saying to check them out, not just go replacing stuff. Sent from my iPhone using Tapatalk
  21. bigcountryguy19

    Steering arm removal

    That's good, glad to hear they came out ok Sent from my iPhone using Tapatalk
  22. bigcountryguy19

    Ball Joint Replacement First Time!

    Never mind lol I had a brain fart, it must set the distance that the ball joint goes in so both joints on the knuckle evenly seat in the axle c. Sent from my iPhone using Tapatalk
  23. bigcountryguy19

    Ball Joint Replacement First Time!

    Preload on what? Sent from my iPhone using Tapatalk
  24. bigcountryguy19

    Steering arm removal

    Just be careful removing it, try to get a stud removal tool if you can, if it breaks off it will be another pita. Sent from my iPhone using Tapatalk
  25. bigcountryguy19

    Ball Joint Replacement First Time!

    I believe that the sleeve for the upper ball joint is for castor adjustment, just make sure it goes back in the same position as the old on so you're alignment stays the same. Sent from my iPhone using Tapatalk

Latest posts

Forum statistics

Threads
42,124
Posts
909,607
Members
33,617
Latest member
dougli1
Top