Search results

  1. D

    Lift kit

    DIXIE PRIDE 85 K20 longbed manuall tranny Sorry i for forgot to say 4" rear Blocks,new 4" arch front springs with 1 1/4 " steel blocks pinned and welded to give the truck a little rake.3 inch body lift and cutout fender flaires. So the cutouts make a huge difference while running 44" mudders on...
  2. D

    Lift kit

    1985 K20 4x4 manual longbed.When i restored my truck i went on the cheap with rough country 4" front springs & 4" blocks in rear,3" body lift I had already i pinned and welded 1 3/8" steel blocks to the front axle pad to give it a little rake. I know they say you should not block the front but i...
  3. D

    Smog thoughts

    Had a shop do my 1985 K20 4x4. No big deal to the them.Removed the smog pumps,hoses and plugged the engine and i took that nasty converter off.Really cleaned up and simplified my 350 motor. In my mind i want to say it runs better but other folks will say it does not make a difference. In MD. i...
  4. D

    Thoughts on going down to 37s?

    Had my 85 K 20 since new 2 sets of 40" 1 set of 42". Was never happy always wanted 44"swampers. Saved & got my 44" after 39 years.it is always what make you happy.If you want them bad enough you will find a way.My Swampers were $639.00 ea 2 years ago now they are almost $1,000 ea.Ig you go with...
  5. D

    Pulling all the smog stuff

    My 85 K20 350 engine is not fuel injected.I had a shop de-smog mine. I had taken the converter off years and went to dual exaust.The shop removed the smog pump and everthing it went to.There is one place in the engine that has to be plugged.My engine looks clean now runs better in my mind than...
  6. D

    2 or 4 inch lift kit

    Did my 85K20 with an 8 foot bed 39 years ago with 4" blocks in rear 4" leaf springs in front with 1.5 blocks,pinned and welded to give it a negative rake in front.No drive shaft mods and only changed my universal joints twice in all the years 66K miles on it I also have 3" body lift & cutout...
  7. D

    Should this new guy buy this '85?

    Bought my 85 K20 new.Sat for 12 yrs finally 2 yrs later got it running again.Stuff like rear drum brakes gas tanks slave cylinder gas and brake lines wheel bearing & seals.Took the bed off replaced the cross members,rocker panel and floor board patch 6K later ,looks great.Yours or the one you...
  8. D

    Do I need different gears with 33” tires and 4” lift

    My 85 K20 manual has 44 swampers on it with stock gears.It is just a 3 speed now i guess ,dont go over 40 mph anyway.It is just a wax and make a beer run on Sunday truck.Had it since new and it never gets dirty anymore.Name on the side of the truck is Reverent Black. Sure love my truck it stays...
  9. D

    4.1 mpg?

    Do not feel too bad my 85 K20 with stock 350 and de-smoked only gets 5 or 6 mpg.3" body lift ,5 suspension with cut out fender flares and 44" super swampers When it was new it got 16 mpg.Pushing them tires mpg went way down.
  10. D

    Fender emblem replacement

    Not advising to do it this way,but i used plastic wall anchors that fit the existing holes good then put JB Weld in the studs and pushed them into the anchor holes. 10 years been holdong good on my 1985 K 20. Not sure if that year has the same setup as yours. 3M tape sounds good they have come...
  11. D

    Charcoal canister delete?

    I have a 85K20 i bought new .It has farm tags so it is exempt from emissions. I took the convertor off years ago and had a shop de-smog my motor take the smog pump and all the stuff off .Only took an hour or so. Engine looks clean now and runs good.
  12. D

    Taillights & blinkers driving me nuts. Not sure what else to check

    I am not an expert just restoring my 85K20 i bought new.Had a simular problem it was the turn signal swithch inside the steering wheel. If affects more lights than just the blinkers. Replaced it and everthing worked fine.Just a thought not sure if this has anything to do with your problem.
  13. D

    I bought a 1984 and don’t know what to do???

    I bought my 1985 K20 new, lot of memories and a lot of fun in it.i recently took off the bed by using my tractor. New gas tanks,brake lines rear brakes on and on.Sanded primed and painted ever inch underside. Once you start you find all kinds of stuff to replace. Bolt are a bitch to remove .Heat...
  14. D

    85 K20 new front driveshaft

    Not saying it is right but i have had my K20 for 38 yrs.lifted Last year i wanted to change out my shocks & front springs looked at RC 6verses 4". Money wise the 4" was a better deal. What i did was put 1 1/2" solid steel blocks under the front springs and drilled holes to accept the centering...
  15. D

    Fuel neck filler hose doesn't fit with new tank

    When i replaced my dual tanks on my 85 K20 my filler hoses were thin say 18ga. medal,they were rusted & could not find replacements in stock. SO i ordered bent SS piping ,you can get about whatever angle you need and cut it to size .Does not have to be exact you will still have a little play in...
  16. D

    Filler neck components

    Just finished a bed off restro on my 85 K20 i have had since new. When i replaced the gas tanks and filler hoses i could not find the both pieces online from say LMC trucks. I ordered Stainless Steel bent piping and made my own. They will never rust out again.Fit good too.Dont forget the ID and...

Latest posts

Forum statistics

Threads
42,311
Posts
913,470
Members
33,810
Latest member
Garcjay
Top