Search results

  1. G

    Wiring ID help - firewall

    ugly truck experience ..utuber who specializes in LS swaps to SB. from horn wiring to lites using ECU underhood fusebox very detailed n simple, using relays
  2. G

    Single tank to dual tank FIX!

    ugly truck experience ...utuber has excellent video using relays n intank pumps ...updated parts, simple description for diy er
  3. G

    Why does it do this

    electric choke uses 12v power supply key on activation, adjust by loosing 3 screws turn CCW and CW watch choke plate move from open to close, at point it is completely closed back off slightly tighten screws, adjust when temps are *32...it will take few times adj. for year round functionality
  4. G

    Printed Circuit Question 79 K10

    aluminum duct tape hvac guys know...somebody makes repair kit for rear window defroster grid that i think is a conductive paint fixes broken grid lines ingenious product
  5. G

    What did you pay for a square

    $300 for '81 swb L6 3spw/OD runs still 102k now 22yrs later 140k mustang buckets, aftermarket center console, 255/60R15 on factory 81suburban alloys, new crank bearings helped boost oil pressure from 0- 35 at idle, brakes, tierods, ball joints, bushings, 1 wire 100amp alt., flex fan, gas shocks...
  6. G

    Tail light brake light issue

    ck bulb socket ground
  7. G

    Wiper washer motor replacement. Who you buying from?

    difference is newer models had delay switch older ones did not, switch must match motor or will not work, possibly damage motor when delay function is activated
  8. G

    1978 305 with rochester 2Gc i believe, its running really werid pls help

    ck cap, rotor carbon tracking n wire ends loose connections, cap too, n continuity, coil output- pull plug wires 1 at time see how far spark jumps couple inches n crisp snap sound is good. ck vacuum at dist. n advance module holds vacuum , distance actuator travels, ck initial timing 6*-8* no...
  9. G

    Swapping from dual to single headlights 1984 Dually

    yep, all interchange , decision now is round or rectangle , '81 square, '79 n older are round get everything from donor, wiring too. possibly bumper too for directionals or parking lts, foot dimmer depends on electrical capabilities
  10. G

    Time to put a sound system in the hotrod, wanna bounce some ideas

    call crutchfield, they'll hook you up for cheap , lotsa choices, most plugnplay connections , no wire cutting, install kits some free, free installation sheets , tell them your budget, they are experts. got me kenwood,5" pioneer front speakers, 6x9 rockford fosgate rear in scoche sealed boxes...
  11. G

    1981? 350 in a C20 - Vacuum/sensor questions

    not needed tvvc, ported vacuum goes to dist., intake vacuum to brake booster, bottom carb vacuum to defrost ball if it has one, same to cruise control vacuum can, choke pull off, one into cab for idiot gauge to moniter engine performance n fuel efficiency. only wires to tranny are reverse...
  12. G

    edelbrock avs2 650

    automatic choke needs properly adjusted, same with timing, too far advanced
  13. G

    Engine sags

    what type fuel pump using? in tank, electric, mechanical , pressure regulator?, even carbs need steady pressure flow, fuel in tank?, tank return line?, tanks vented?, caps venting?, bad gas?, check for water n debris use glass or see thru container, how old is coil? might be overheating n...
  14. G

    Truck pulls to the right.

    my guess is caliper on right side locking up, due to excessive wear either from pads or rotor or both. cud also be dirty piston,seal allowing debris into chamber, wore out cylinder where piston gets jammed up at end of its travel n wont return back into caliper to free up rotor to spin. caliper...
  15. G

    Alternate Steering Wheel

    I like Grant, many options to choose from
  16. G

    alternator up grade!

    you might have to reclock it depending on where its clocked and if wiring harness will reach
  17. G

    Engine loses power when shifting gears(auto)

    very well cud be timing, bent valve, bent push rod, vacuum leak, or what my first thot carburator float level needs adjusted or replaced. motor not getting enough fuel and starts running low after second gear. is engine warmed up? like idling for 15 minutes or more? smog pump still connected...
  18. G

    Can you make a 305 stroker with 350 crank and rods?

    I'm not sure what rod you used 3.48 is stock rod length. from center point wrist pin to flat surface of block can not change or lowering compression cause you cannot increase piston height without head interference. I dont know rod length in an OPAL , but I do know a friend who used 350 pistons...
  19. G

    timing chain replacement selection advice / what if got after opening it up

    I run a dbl roller in 327 with no issues. just guessing most 305's had a fiber cam gear, with tendencies to start chipping off pcs over 100k miles, low budget buy new stock chain n new all steel cam gear, unless crank gear is severely worn will be ok, gears are cheap and better as new set. shop...
  20. G

    Can you make a 305 stroker with 350 crank and rods?

    ah no, by changing rods , you need diff pistons with rod hole up higher or closer to rings, I'm pretty sure nobody makes them. just like 383, by changing crank in 350 , pistons wud come up outta cylinder 1/4" . head wud never bolt on, but since chevy performance made a crate 383, most top line...
  21. G

    Opinions on an Engine Swap for 81 C10

    expect alotta luck for $1500 w/ economy. I got a 2000 chevy metro 400K still runs, but very rough, i think couple burnt valves, new tires, i have spare engine from my '92 has rebuilt head ,simple head swap 2 or 3 yrs left in her..50mpg...your not gonna rebuild nothing of quality for 1500. cept...
  22. G

    Can you make a 305 stroker with 350 crank and rods?

    yes partially right 400 crank into 350 block 4" bore plus 400 rods with 3.75" stroke special made piston to accommodate for long stroke is also internally balanced so also is needed harmonic balancer off 400 n flexplate or flywheel off 400. why the 383, the 400 was susceptible to overheating due...
  23. G

    Can you make a 305 stroker with 350 crank and rods?

    No you can NOT make 305 stroker, wud require longer connecting rods as 305 uses same crank as 350, bore is 3.75 where 350 has 4." bore. totally diff block, not enough metal to open bore up that far, possibly get .030 over ,but blocks are boat anchors, way more torque use a inline six. 305 is...
  24. G

    Need help - Brakes still spongy

    Most of problems got mentioned, but one. Possibility you have collapsed brake lines. meaning old n brittle but not leaking , YET. if any are showing signs of old age, and you didn't replace them also, after one more try at bleeding, starting with bench bleed, going slowly n positive lines stay...
  25. G

    Opinions on an Engine Swap for 81 C10

    some time has past , n curious to know how project is moving along and cost of to present/finished? to add lil info to thread of doing rebuild yourself is not something i'd recommend without some education beforehand eg. highschool engine class, college coarse of mechanical theory. some of tools...

Latest posts

Forum statistics

Threads
42,253
Posts
912,248
Members
33,755
Latest member
BugRedC10
Top